1982/03/17 Caterpillar


Heavy Duty Air Cleaner Available, With Precleaner And Automatic Dust Ejector

Usage:


3406 Industrial And Generator Set Engines

Description of Change: Engine-mounted heavy duty air cleaner systems are now available for 3406 Industrial and Generator Set Engines. The new system uses a centrifugal (cyclone-type) precleaner to remove up to 95% of the dust from the air before it goes into the air cleaner. A dust ejector muffler or exhaust pipe is also used, with a tube connected to the precleaner. The venturi action of the dust ejector removes the dust from the precleaner through the tube, and the dust is then discharged with the exhaust. This automatically keeps the precleaner empty.

The air cleaner used with the system is a two-stage dry-type, with primary and secondary elements. An air cleaner service indicator is part of the group. This air cleaner, with the precleaner and automatic dust ejector, will extend service intervals and improve performance in engine applications where there are large amounts of dust in the air.

Adaptable To: The new air cleaner systems are currently available, and can be ordered as original equipment on new engines according to the engine specifications as shown in Chart A, except engines equipped with water-cooled manifolds. Also, the new air cleaner system can be installed on earlier 3406 Engines 90U1-Up and 75Z1-Up, except those equipped with water-cooled manifolds. The new air cleaner system is not adaptable to engines which have water-cooled manifolds. The new system can be adapted to enclosed package generator sets, but a modification is necessary. A small change must be made to the location of the hole in the enclosure for muffler installation.

For conversion of earlier engines, five different groups are needed, as follows:

1. One 8N9759 Air Cleaner Mounting Group.
2. One 8N9710 Exhaust Elbow Group.
3. One air cleaner group. See Chart B.
4. One precleaner group. See Chart B.
5. One muffler group or exhaust pipe group. See Chart B.

Most of these groups can be ordered only as separate parts (except some precleaner groups as shown in Chart B). After selection of the correct groups, check each group in the NPR and order the separate parts as shown in column three.


Location of air cleaner parts and service indicator fittings.


Location of mounting group parts.

Caterpillar Information System:

1982/03/17 Improved Bearing Used In Rear Power Takeoff Groups
1982/03/17 New Gasket Used In Governor And Fuel Injection Pump Group
1982/03/17 Correct Lubrication Procedure Will Prevent Damage To Fan Drive
1982/03/17 New Adapters And O-Ring Seals Used In Aftercooler Group
1982/03/17 New Diaphragm Used In Fuel Ratio Control
1982/02/24 Use The Correct Governor For Parallel Applications
1982/02/24 Use 6V6035 Hardness Tester On Crankshafts
1982/02/24 New Idler Shaft Used In Fuel Transfer Pumps
1982/02/24 New Inlet And Exhaust Valves And Exhaust Inserts Available
1982/02/24 New Poppet Valve Will Decrease Chatter
1982/02/24 New Main Bearings And Connecting Rod Bearings Have Thicker Layer Of Surface Material
1982/02/24 Engine Storage; Engine Start-Up After Storage
1982/03/17 New Double-Wall Fuel Injection Lines Group And Fuel Drain Group Available As Attachments For Protection Against Fuel Leakage
1982/03/17 Brass Plug Used To Prevent Corrosion
1982/04/07 Reconditioning Of Bridge Wear Seat Is Permitted; Will Prevent Bridge Replacement When Not Necessary
1982/04/07 Location Of Sending Unit Changed To Improve Accuracy Of Water Temperature Indication
1982/04/07 Engine Replacement
1982/04/07 Use The 6V6059 Microlite With The 6V2196 Inspection Microscope
1982/04/07 Caterpillar Electric Starting Motors
1982/04/07 List Of Service Publications
1982/04/07 Use 5P5195 Fuel Line Wrench Correctly
1982/04/07 New Marine Gear Groups Have New Clutch Plates
1982/04/07 Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/04/07 New Oil Pump Outlet Elbow Is Stronger
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.