1980/09/10 Caterpillar


New Oil Scavenge Tube Assembly Used In Oil Lines Group

Usage:


D353 Industrial And Marine Engines

Description of Change: A new oil scavenge tube assembly is used in the oil lines groups for D353 Industrial and Marine Engines. The new oil scavenge tube does not have a support bracket near the oil pump.

Failure of the support bracket nearest the oil pump was some times possible on the former oil scavenge tube.

Test results have shown the brackets are not necessary.

Adaptable As: The new 5N7456 Oil Scavenge (Rear) Tube Assembly is a direct replacement for the former 9M1011 Oil Scavenge (Rear) Tube Assembly which is canceled. The L364 Locknut and S509 Bolts, used with the former tube assembly, are not needed.

Caterpillar Information System:

1980/09/10 Special Cup Plugs For Use In Oversize (Larger Than Standard Size) Bores In Valve Rocker Arm Shafts
1980/09/10 6V3025 Battery Cable Repair Kit Now Available{1402,1408,0611}
1980/09/10 New Oil Filter Base Has Larger Oil Passages; Some Bases Need Modification
1980/09/10 6V2119 Profile Tool Group Is Available For Inspection Of All Crankshafts In Caterpillar Engines
1980/09/10 CAUTION: Procedure For Adjustment Of Fuel Rack Setting On Hydramechanical Governors Has Been Changed
1980/09/10 Reference List Of Pistons Used With The Different Types Of Connecting Rods
1980/09/10 6V2086 And 6V2087 Seal And Wear Sleeve Installers Available
1980/09/10 Cartridge Repair Kit Available For AiResearch Turbochargers
1980/09/10 List Of Service Publications
1980/09/10 Easy-To-Make Tool Holds Fuel Injection Nozzles According To Cylinder Number
1980/09/10 Oil Pump And Lines Group Changed To Use Different Method Of Flow Control For Emergency Lubrication System{3310,3311}
1980/09/10 Special Bolts Available For Better Protection Against Modifications Of Fuel System And Governor Settings
1980/10/01 Protect Your Reconditioned Or Rebuilt Engines During Start-Up
1980/10/01 Fretting Material Must Be Removed Before Installation Of New Bearings
1980/10/01 Install A New Oil Filter Element, Clean The Oil Lines And The Remote Filter Base; Turn The Engine Until The Oil Gauge Shows Pressure Before Starting A Rebuilt Engine
1980/10/01 New Breather Groups Used
1980/10/01 Woodward 2301 Speed Control (8N1731 Speed Control Group) Can Be Adapted For Use As Field Test Instrument
1980/10/01 List Of Service Publications
1980/10/01 Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies
1980/10/01 Reverse Flow Check Valves And Check Valves With A Groove Can Not Be Used In Place Of Each Other
1980/10/01 New Timing Advance Weight Used
1980/10/01 6V3071 Seal Guide Keeps Seal In Position During Installation Of Transfer Pump
1980/10/01 Do Not Use Room Temperature Vulcanizer Compounds Or Silicone Rubber Cements On O-Ring Seals In Engines; Do Not Use Too Much As Gasket Material
1980/10/01 Use Starter To Turn Crankshaft For 30 Seconds Or Until Oil Pressure Gauge Shows Pressure, Before Engine Is Started
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.