1980/04/30 Caterpillar


Main And Connecting Rod Bearings With Cavitation Erosion Can Be Used Again

Usage:


D346, D348, D349 Engines In All Applications

According to field reports, some dealers and customers have installed replacement main and/or connecting rod bearings in the above model engines when the bearings were found to have cavitation erosion (see the illustration). Cavitation erosion is caused by normal rapid changes in oil pressure at specific locations on the bearing during engine operation. A pressure decrease permits the development of small bubbles in the oil which break when the pressure increases again. When the bubbles break, it causes the application of a force against the bearing surface. After many cycles, the application of force to the bearing metal causes small pieces of the lead-tin surface layer to come off as shown in the illustration. This is cavitation erosion.


Typical example of cavitation erosion.

Normally, cavitation erosion will not cause bearing failures for these reasons:

... The very small size and amount of debris caused by cavitation erosion.
... The location of the cavitation erosion on the bearing surface. The location is generally near the separation at the ends of the bearing as shown in the illustration; not in the "load area".

When cavitation erosion is found during an inspection of main and connecting rod bearings, the recommendation is to use the bearings again unless there are other indications of wear and/or damage.

Caterpillar Information System:

1980/04/09 Caution: Outboard Bearing Must Be Removed From Extended Shaft Of Front Power Takeoff Before The Engine Is Moved
1980/04/09 Important: Use Only 12 Volts Direct Current To Boost Start 3208 Truck Engines Equipped With Exhaust Gas Recirculation Systems
1980/04/09 Remanufactured Short Blocks Are Available For Repairs Of Early 3406 Engines
1980/04/09 Different Water Temperature Regulators Now Used To Prevent Overheating
1980/04/09 Dowtherm 209 Full-Fill Coolant
1980/04/09 6V2023 Flow Check Adapter Group Is Available
1980/03/12 New Control Valve Body
1980/03/12 Crankshaft Rear Seal And Wear Sleeve Are Now Serviced As A Group Instead Of Separate Parts
1980/03/12 List Of Service Publications
1980/03/12 Spacer Plate Block Group Used For Parts Service Of Block Group With Counterbore Design
1980/03/12 New Fuel Injection Lines And Clamps Prevent Stresses And Contact Which Can Cause Leakage
1980/03/12 Stronger Braces Used Between Air Cleaner And Engine
1980/04/30 Wrong Installation Of Oil Cooler Gasket Can Cause High Oil Temperatures
1980/04/30 Boring Machine, Adapter Groups And Sleeves Available For Repair Of Damaged Cylinder Blocks
1980/04/30 Crankcase Capacity Increased And New Oil Level Gauges Used; Specifications For Conversion Of Existing Gauges
1980/04/30 List Of Service Publications
1980/04/30 Hardened Washers Now Used On Bolts For Fan Shroud
1980/04/30 Improvements Made To Water Separator Groups
1980/04/30 New 1N3270 Auxiliary Drive Group Available As Attachment
1980/04/30 Different Vibration Damper Now Used
1980/04/30 New Top Piston Ring Has Plasma-Coated Face
1980/04/30 New Liner Seat Insert For No. 1 And No. 4 Cylinders Of D353 Engines
1980/05/14 New 6V2120 Spline Sprocket Improves Depth Control Of 5P4175 Boring Tool Group
1980/05/14 Changes To 9S240 Rack Position Tool Group; Revision To Special Instructions
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.