1979/10/03 Caterpillar


Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters

Usage:


A quick-disconnect coupling can be installed on the 5P4150 Nozzle Tester to permit more rapid exchange of nozzle adapters. If you make this modification to your nozzle tester, the 5P4721 Tube must be made shorter.


5P4721 Tube in position.


NOTICE

The length of tube removed for the capsule-like nozzle adapter must be exactly 66 mm (2.6").


The volume of test fluid in the new parts is the same as in the length of tube removed. The basis of the "Pressure Loss Test" is the volume of fluid in the original system. The length of the tubes for the other adapters is not important.

To install the quick disconnect coupler, follow these instructions and use only the parts given here:

1. For each nozzle adapter, remove 66 mm (2.6") from the short end of a 5P4721 Tube.

2. Remove the burrs from the cut ends and thoroughly clean the tubes.


5P9701 Coupler Assembly.

3. Install a 5P4719 Fitting Assembly and a 5P9715 Nipple on the cut end of each tube. See Special Instructions, Form SEHS7292 "Use of 5P4150 Nozzle Testing Group and 8S2245 Nozzle Cleanup Kit" for correct assembly instructions.

4. Install the adapters on the other end of each tube. Use 3J1905 Sleeves and 3J1906 Nuts (parts of 5P4719 Fittings and 5P4720 Elbows). Use Special Instructions Form SEHS7292 for correct assembly instructions.

5. Remove the original tube assembly and 5P4719 Fitting from the tester.

6. Install a 5P9701 Coupler Assembly.

Caterpillar Information System:

1979/09/19 6V2055 High Vacuum Grease Gives Better Oil Seal
1979/09/19 Improved Sea Water Pump Now Used
1979/09/19 New Liner Seat Inserts For Spacer Plate Cylinder Blocks Are Made Of Stainless Steel
1979/09/19 Stronger Bolt Now Used With Exhaust Manifold
1979/09/19 Raw Water Pump Improved
1979/09/19 Cranking Speeds Necessary To Start Diesel Engines
1979/09/19 New BrakeSaver Control Valve Group Has Improved Diaphragm
1979/09/19 New Gasket Used In Water Lines Group For Aftercooler
1979/09/19 Electrical System Voltage Must Be Limited To A Maximum Of 40 Volts With Woodward Model 2301 Governors.
1979/09/19 New Bracket Available For Installation Of Jacket Water Heater
1979/09/19 Service Kit Is Available For Woodward UG8 Governor
1979/09/19 Pin Bore Is Now Offset (Not In The Center) .059" (1.5 mm) In The Piston To Stop Vibration Of The Cylinder Liners Which Can Cause Pitting On The Coolant Side Of The Cylinder Liners
1979/10/03 Steel Plates Are Now Used To Hold The Element In Position In The Panel-Type Air Cleaner Housing Assembly
1979/10/03 Different Mounting Hole Locations In Ring Gear Plate Assembly And Rotor Assembly For BrakeSaver
1979/10/03 List Of Service Publications
1979/10/03 Tips For SIRS (Service Information Retrieval System) Users
1979/10/03 Recommendation For Use Of A FLEX-HONE On 1100, 3100 and 3200 Series Engines
1979/10/03 New Aftercooler Core Has Stronger Construction And Corrosion Resistance
1979/10/24 New Hydromechanical Shut-Off Is Available
1979/10/24 Cold Temperature Starting Procedures For Air Compressor And Drill Engines
1979/10/24 New Camshaft Housing Gasket Has Increased Resistance To High Temperature
1979/10/24 Improved Seal Used In Raw Water Pump On Marine Engines
1979/10/24 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U.S. FActories
1979/10/24 New Coolant Temperature Regulator Housing And Vent Line Valve Give Better Control Of Engine Cooling; Conversion Kits Available.
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.