1982/12/08 Caterpillar


Make Change To 6V2100 Multitach And 5P9698 Calibrator

Usage:


Some changes are necessary to the 6V2100 Multitach and 5P9698 Calibrator for correct operation. These changes are listed below.

Changes To 6V2100 Multitach

RPM indications on the 6V2100 Multitach can be in error when either the tachometer generator or magnetic pickup is connected to the MAG input at the same time a 6V4950 Injection Line Speed Pickup Group is connected to the PHOTO input. A resistor located on the printed circuit board inside the multitach must be changed to correct the problem.

Procedure To Change 6V2100 Multitach

1. All 6V2100 Multitachs built after July 1, 1982 have had the resistor changed at the factory. These units have the letter "A" on the end connector panel next to the 11 to 40 volt DC connector. See Illustration 1. Check to see if your multitach has this letter.

2. For those multitachs which have not had the problem corrected and have no letter "A" on the connector panel, a resistor must be purchased from an electronic supply store. The resistor needed is a 220 k ohm ±10%, 1/4watt carbon resistor.

3. Remove the rear cover of the multitach as shown in the Special Instruction, "Using the 6V2100 Multitach," Form SEHS7807-01, Page 17. It is possible that the printed circuit board will also have to be removed.

4. Remove resistor R16 from the printed circuit board. See Illustrations 2 and 3. This is done with the application of heat from a small soldering iron. Use heat on the lead wires on each end of the resistor until the solder melts and the resistor can be lifted from the printed circuit board. Use needlenose pliers or a 5P1720 Oil Seal Pick to lift the resistor.

5. Install the new 220 k ohm resistor in the location where resistor R16 was removed.

6. Check resistor R15 to see if it is in direct contact with the printed circuit board. See Illustration 3. There must be approximately 1.0 mm (.04 ") of clearance between the body of the resistor and the printed circuit board. If there is no clearance, use heat on the lead wire on one end of the resistor. Lift this end of the resistor with an oil seal pick when the solder melts. Do the same procedure on the lead wire on the other end of the resistor. Replace the rear cover on the multitach and make a test according to the procedure in the Special Instruction.


Illustration 1. Identification mark after change is made to 6V2100 Multitach.

7. Use a letter stamp or engraving tool to permanently mark a letter "A" on the connector panel, as shown in Illustration 1.

Changes To 5P9698 Calibrator

The 6V6113 Amplifier, which is part of the 6V4950 Pickup Group, will test as bad when test procedures are done unless a resistor in the 5P9698 Calibrator is changed.

Procedure To Change 5P9698 Calibrator

1. All 5P9698 Calibrators built after July 1, 1982 have already had the problem corrected at the factory. These units have the letter "C" after the serial number on the front panel. Check to see if your calibrator has this letter.

2. For those calibrators which have not had the problem corrected and have no letter "C" after the serial number, the part needed must be purchased from an electronic supply store. The part needed is a 1 k ±ohm 10%, 1/4watt carbon resistor.

3. Remove the four screws on the corners of the front panel and lift the front panel out of the case. Locate and remove resistor R6, as shown in Illustration 4. This is done with the application of heat from a small soldering iron. Use heat on the lead wires on each end of the resistor until the solder melts and the resistor can be lifted from the printed circuit board. Use needlenose pliers or a 5P1720 Oil Seal Pick to lift the resistor.

4. Install a new 1 k ohm resistor in the location where resistor R6 was removed.

5. Use a letter stamp or engraving tool to permanently mark a letter "C" on the front panel after the serial number. Use caution not to damage the electrical circuits. Install the front cover in the case.

6. Locate resistor R6 at the top of the parts chart in the Special Instruction, "Maintenance and Troubleshooting of 5P9698 Calibrator," Form SMHS7504, Page 7. Change the description from 2.2 k ohm to 1.0 k ohm and change the Flo-Tech part number from 1383-2.2 k to 1383-1.0 k.

NOTE: The procedure on Page 7, Section B, "Checking The 6V1114 Pickup " in Special Instruction, "Using the 6V4950 Injection Line Speed Pickup Group, " Form SEHS8029, can still be done even if the procedure in Section A to test the 6V6113 Amplifier shows the amplifier to be bad.

Repair Centers

The repair centers in the list which follows will repair the multitach and calibrator for a small service charge. Send the 6V2100 Multitach to this address and ask that change "A" be made to it.

General Fabrication Corporation
1100 S. W. 11th Avenue
Industrial Park
Forest Lake, MN 55025
U.S.A.
Phone: 612-464-5110

Send the 5P9698 Calibrator to this address and ask that change "C" be made to it:

Flo-Tech, Inc.
403 South Washington Blvd.
Mundelein, IL 60060
U.S.A.
Phone: 312-566-9120


Illustration 2. Location of R16 and R15 resistors in 6V2100 Multitach.


Illustration 3. Location of R16 and R15 resistors in electronic diagram of 6V2100 Multitach.


Illustration 4. Location of R6 resistor in 5P9698 Calibrator.

Caterpillar Information System:

1982/10/27 Changes In Engine Rpm; Governor Does Not Operate Correctly
1982/10/27 Bulged Capsule-type Fuel Nozzles
1982/10/27 Additional 3208 Remanufactured Truck Engines Available
1982/10/27 New Fuel Nozzle Test Sheet Available
1982/10/27 Fuel In The Cooling System Or Coolant In The Engine Oil Can Result From Cracked Fuel Nozzle Adapter
1982/10/27 Wider Crankshaft Gear Used
1982/10/27 New Oil Additives Can Cause High Copper (cu) Indications During S.o.s. Tests
1982/10/27 Dial Bore Gauge And Size Setting Fixture Available
1982/10/27 Indications From 6V3100 Timing Indicator Group Must Be Corrected For Some Applications
1982/10/27 Service Information For Easier Use Of The 6V3100 Timing Indicator Group
1982/10/27 Engine Slobbering; New Piston And Rings Used
1982/10/27 New Fasteners Used For Fuel Injection Lines
1982/12/08 New Seal Used On Governor Control Shaft
1982/12/08 New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip
1982/12/08 6V6142 And 6V6143 Installers Can Be Used To Install Crankshaft Seals And Wear Sleeves
1982/12/08 Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/08 New Crankshaft Seal Groups Used
1982/12/08 6V4869 Adapter And 6V6174 Plug Can Be Used To Install Camshaft Bearings
1982/12/08 Resurfaced Cylinder Blocks And Heads
1982/12/08 List Of Service Publications
1982/12/08 6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier
1982/12/08 Improvements Made To Fuel Ratio Control
1982/12/08 Removal Of Hydraulic Override From Fuel Ratio Control
1982/12/08 Use 6V6147 Polishing Wheel To Clean Piston Pins
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.