1981/09/09 Caterpillar


Troubleshooting The Fuel Ratio Control Group For Low Power Complaints

Usage:


3406, 3408 Truck Engines

Many low power complaints for the above engines are the result of problems in the fuel ratio control group. The four major areas to check are the diaphragm, seals, housing and valves.


Areas to check when troubleshooting fuel ratio control groups.

Diaphragm And Gaskets

The diaphragm must be tested for air leaks caused by distortion during assembly or by small holes. To do this, connect a 70 kPa (10 psi) air source and a pressure gauge to the boost tap on the fuel ratio control housing. The air source must have a regulator and shut-off valve. Charge the fuel ratio control to 70 kPa (10 psi) and shut off the air valve.

Watch the gauge for an indication of an air leak. While the control is charged, put some water and soap solution around the covers to check for air leakage between the gasket and covers. If there is leakage, install a new diaphragm or gasket as necessary.

Teflon Seal And O-ring

The limiter valve assembly has an O-ring seal behind the Teflon seal on the piston. It is possible for the O-ring seal to swell (increase in size) when it is hot and cause the Teflon seal to stick in the housing. The Teflon seal will not stick at room temperature. To check the seals, heat the housing and valve in oil to 82 °C to 93°C (180°F to 200°F). If the limiter valve assembly moves freely, the O-ring did not swell and the Teflon seal did not stick.

Machined Bore In Housing

Check the housing for a rough, machined bore. The bore must be shiny in comparison to the casting surface, and it must feel smooth against a finger nail.

On engines which have 161000 km (100,000 miles) check the bore for visible wear. The worn bore permits side movement of the limiter valve assembly.

If the bore is rough or worn, install a new housing.

Limiter Valve Assembly

The limiter valve, used in the limiter valve assembly, has four oil holes with an oil groove under the holes. Burrs on the oil groove will not let the internal valve, which fits into the limiter valve assembly, move freely. If the internal valve does not move freely, the driver must shift to lower gears during operation on a hill.

To correct this problem, use a round file, emery cloth and lapping compound to remove the burrs. Be careful to remove only the burrs. Also, do not remove any material from the internal valve.


NOTICE

This must be done very carefully to prevent damage to the bore of the limiter valve.


Caterpillar Information System:

1981/08/18 New Information System For Engine Gasket Kits
1981/08/18 New Spacers Used With Larger Valve Springs
1981/08/18 Use 6V4805 Valve Seat Extractor Group To Remove Valve Seat Inserts
1981/08/18 Indications Of High Oil Temperatures In Brakesaver Circuit Can Be Caused By Wrong Gauge Connection
1981/08/18 Coolant Conditioner Elements And Their Capacities
1981/08/18 Use 6V4068 Tool Group To Machine Camshaft Thrust Face
1981/08/18 Mailing Of Engine News And Truck Engine News Microfiche Libraries
1981/08/18 Delay Expected In Replacement Of Canceled Service Tools
1981/08/18 Remove Piston Cooling Tubes Before Removal Of Pistons And Connecting Rods
1981/08/18 All Size Identification Marks On Engine Bearings Are Now Shown In Millimeters
1981/08/18 Some Parts Books And Microfiche Show Wrong Governor And Fuel Pump Drive Groups For Specific Engines
1981/08/18 Instruction Cards For "Go-No Go " Gauges Now Available
1981/09/09 Use Of Different Anti-seize Compound Prevents Problems With S.O.S. Tests
1981/09/09 O-Ring Seal Materials And Applications: Use Only The Correct Seal For The Specific Installation
1981/09/09 Certification Film Necessary On Engines Adjusted For High Altitude Operation
1981/09/09 Standard Interval For Oil Changes Now 20,125 Kilometers (12,500 Miles) Or 250 Service Hours
1981/09/09 Improvements To Optional Modification Of 5P4150 Nozzle Tester
1981/09/09 6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation
1981/09/09 Different O-ring Seals Used In Exhaust Gas Recirculation Actuator Group
1981/09/09 Top Rings For Pistons Have Two Designs
1981/09/09 New Idler Pulley Groups Improve Service Life Of Vee-belt
1981/09/09 List Of Service Publications
1981/09/09 Explanation Of Differences In Timing Advance Information
1981/09/09 Thrust Washer Used In Pump Housing For Sleeve Metering Fuel System
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.