1980/02/11 Caterpillar


Warning: Avoid Use Of Fuel Mixtures Of High Volatility. If You Are Exposed To Such Mixtures, Be Aware Of The Hazards Involved And Take Proper Precautions{1280}

Usage:


Diesel fuels combined with gasoline, naphtha, or other highly volatile fuels can be dangerous. BECAUSE OF THE SAFETY HAZARDS INVOLVED, CATERPILLAR DOES NOT RECOMMEND THE USE OF GASOLINE/DIESEL FUEL OR NAPHTHA/DIESEL FUEL BLENDS. Extreme caution must be exercised when these volatile fuel mixtures are present.

Gasoline and naphtha are light aromatic distillates of petroleum. When either of these fuels are combined with diesel fuel (No. 1 or No. 2) or kerosene, fuel blends of high volatility can result. The volatility of these blends could lie in a dangerous range even if a small percentage of gasoline or naphtha is added to the diesel fuel.

In a fuel tank, the vapor in the air space above pure diesel fuel is too lean to be a hazard at normal ambient temperatures. The vapor in a tank that contains pure gasoline or naphtha is too rich. However, when diesel fuel is mixed with gasoline or naphtha, the vapor-to-air ratios can be explosive. This vapor above the fuel in the fuel tank can be ignited by sparks, flames, electric arcing, and even static electric charges.

There are several reasons why such fuel blends are used. The most common is probably to combat fuel filter plugging problems (waxing) experienced in cold temperatures. Also in some areas, diesel fuel may be in short supply while gasoline or naphtha is readily available. Users may blend the fuels to extend the diesel fuel supply.

Mechanically, Caterpillar engines can accept certain proportions of gasoline or naphtha blended with diesel fuel without major effects on performance or engine life.

With this in mind, it is quite possible that hazardous fuel blends will be used by diesel equipment owners and operators--especially during periods of cold temperatures. It is for this reason, personnel who work with, on, or near diesel-powered equipment should be made aware of the safety hazards involved. SAFETY PRACTICES WHICH MAY HAVE WORKED WELL WHEN IN CONTACT WITH PURE DIESEL FUEL WILL NOT BE ADEQUATE WHEN DEALING WITH THESE BLENDS.

As it will be difficult at times to detect the usage of a fuel blend, we recommend that the following precautions be observed by personnel in contact with diesel fuels and diesel-powered equipment:

1. Do not smoke in areas where fuels are handled or used.
2. Keep heat sources, flames, sparks, electric arcing, etc. well away from storage or service tanks.
3. Prevent careless handling, fuel spillage, and tank leakage and exercise the above precautions if accidental spillage does occur.
4. Handle all fuels only in well ventilated areas.
5. Make sure that storage tanks are vented outside of buildings or enclosures and never into unventilated areas.
6. When transferring fuels from one tank to another, ensure that both tanks are grounded to a common ground or that they are electrically connected or bonded.
7. Always keep first aid and fire extinguishing equipment that is suitable for use on oil fires maintained and within easy access.

We recommend that this information be brought to the attention of all personnel who have contact with diesel fuels and diesel-powered equipment.

Refer to the articles "Fuel Heaters Are Now Available For Field Installation", SERVICE MAGAZINE, January 7, 1980 and "General Information--Diesel Fuels In Cold Temperature Operation", SERVICE MAGAZINE, December 17, 1979, for practical and safe solutions to cold temperature operation problems.

------ WARNING! ------

THE USE OF FUEL HEATERS IN COMBINATION WITH HAZARDOUS FUEL BLENDS SHOULD BE AVOIDED. FUEL VOLATILITY INCREASES AS FUEL TEMPERATURE INCREASES.

-------WARNING!-------

Caterpillar Information System:

1980/02/04 Real Value Available Through Caterpillar Remanufacturing Programs{0374}
1980/02/04 Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04 New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower{1216}
1980/01/28 Oil Drain Hole Added To Spacer Plate Cylinder Block To Permit Use Of Scroll Fuel System{1201,1221}
1980/01/28 New Attachment Air Compressor Group and Lines Groups Have Improved Design{1065}
1980/01/28 Installation Procedures For 5N5880 Remote Shut-Off Group And 5N6336 Oil Pressure Indicator Gauge Group{7418,7403,7455}
1980/01/28 New 6V199 Socket For Use On Fasteners In Areas With Limited Clearance{0612}
1980/01/21 New Fuel Injection Nozzle Assembly Used{1254}
1980/01/21 Extended Shafts Now Available For Front Power Takeoff Units{3055}
1980/01/21 Cooling System Improvements Prevent Expansion Tank Leakage{1354,1380,1153}
1980/01/21 New Piston Groups Have The Piston Pin Bore Off-Center, Away From The Thrust Side Of The Piston{1214}
1980/01/21 A Spring With A Lower Rate Is Now Used In The Fuel Filter Group To Give Less Fuel Pressure{1261}
1980/02/11 Use The Correct Water Temperature Contactor{1350,1100}
1980/02/25 How To Check Operation Of Hydramechanical Shutoffs On D379B, D398B, D399 Engines{7418}
1980/02/25 Revision Of Special Instruction Form No. SMHS7267, "Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets" Has Important Changes{1307}
1980/02/25 Stronger Braces Used Between Air Cleaner And Engine{1051}
1980/02/25 Plunger Movement Must Be Adjusted When New Rack Shut-Off Solenoid Is Installed{1259}
1980/02/25 Drawings Available For Six Tools Used During Repairs Of Damaged Pin Bores In Two-Piece Booms{6501,0665}
1980/02/25 Identification Of Fuel Injection Lines And Nozzle Bodies For Different Combustion Systems{1252,1254}
1980/03/03 Spacer Plate Block Group Used For Parts Service Of Block Group With Counterbore Design{1101,1201}
1980/03/03 Connecting Rod Changes And Replacement Information{1218}
1980/03/03 Fuel Heaters Are Now Available For Field Installation{1296}
1980/03/24 Inspect Regulator Cover Assembly When Overcooling Is A Problem{1350,1380}
1980/03/24 Crankshaft Rear Seal And Wear Sleeve Are Now Serviced As A Group Instead Of Separate Parts{1161}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.