D399, G399, D398, G398, D379, G379 ENGINES Caterpillar


Governor; (7L8787, 8L5814 and 7L4352)

Usage:

(1) 8M9141 Spring for governor high idle:

Load under force of ... 6.30 lb.(2,85 kg)

Then compress an additional ... .370 in.(9,398 mm)

Total test force reading ... 10.75 ± .20 lb.(4,88 ± 0,09 kg)

Free length after test ... 2.340 ± .030 in.(59,44 ± 0,76 mm)

Outside diameter ... 1.371 ± .015 in.(34,82 ± 0,38 mm)

(2) Torque for locknut ... 11 ± 1 lb. ft.(1,52 ± 0,14 mkg)

NOTE: On natural gas engines, adjustment of stop screw should limit governor stop collar travel to .605 in. (15,37 mm) from fuel off position.

(3) 8M6303 Spring for inner thrust:

Length under test force ... .18 in.(4,57 mm)

Test force ... 9.5-10.5 lbs.(4,3-4,7 kg)

Free length after test ... .344 in.(8,74 mm)

Outside diameter ... .478-.482 in.(12,14-12,24 mm)

(4) Torque for 3/8 in. nut ... 36-48 lb. in.(41,5-55,3 cm.kg)

Torque for 1/4 in. bolt ... 6-12 lb. ft.(0,83-1,66 mkg)

(5) Diameter of pump shaft bearing upper journal ... .6265-.6271 in.(15,913-15,928 mm)

Bore in the cover ... .6313-.6323 in.(16,035-16,060 mm)

(6) Distance bearing extends ... .465-.475 in.(11,81-12,06 mm)

(7) Clearance between pump gear and cover ... .0009-.0021 in.(0,023-0,053 mm)

(8) Diameter of new idler gear bearing ... .8107-.8113 in.(20,592-20,608 mm)

Bore in new pump idler gear ... .8125-.8135 in.(20,638-20,663 mm)

(9) Diameter of new drive shaft lower journals ... .6855-.6865 in.(17,411-17,437 mm)

Bore in the housing ... .6875-.6885 in.(17,462-17,488 mm)

(10) Shaft end play ... .02-.06 in.(0,5-1,5 mm)

Caterpillar Information System:

D399, G399, D398, G398, D379, G379 ENGINES Cylinder Head
D399, G399, D398, G398, D379, G379 ENGINES Connecting Rod
D399, G399, D398, G398, D379, G379 ENGINES Piston And Rings
D399, G399, D398, G398, D379, G379 ENGINES Cylinder Block
D399, G399, D398, G398, D379, G379 ENGINES Prelube Pump; (Later Type)
D399, G399, D398, G398, D379, G379 ENGINES Prelube Motor Relay; (Later Type)
D399, G399, D398, G398, D379, G379 ENGINES Prelube Pump Motor; (Later Type)
D399, G399, D398, G398, D379, G379 ENGINES Prelube Oil Pump And Motor; (Early Type)
D399, G399, D398, G398, D379, G379 ENGINES Vibration Damper
D399, G399, D398, G398, D379, G379 ENGINES Manifold
D399, G399, D398, G398, D379, G379 ENGINES Temperature Regulator
D399, G399, D398, G398, D379, G379 ENGINES Fresh And Auxiliary Water Pumps; (4L8800, 6L8983, 6L4754, 2N955 And 7L3222)
D399, G399, D398, G398, D379, G379 ENGINES Flywheel
D399, G399, D398, G398, D379, G379 ENGINES Flywheel Housing
D399, G399, D398, G398, D379, G379 ENGINES Fuel Ratio Control; (8S6419)
D399, G399, D398, G398, D379, G379 ENGINES Silicon Controlled Ignition System; (Solid State Magneto)
D399, G399, D398, G398, D379, G379 ENGINES Generator Coil; (Solid State Magneto)
D399, G399, D398, G398, D379, G379 ENGINES Pulser Coil; (Solid State Magneto)
D399, G399, D398, G398, D379, G379 ENGINES Magneto Timing Setting; (Solid State Magneto)
D399, G399, D398, G398, D379, G379 ENGINES Transformer; (Solid State Magneto)
D399, G399, D398, G398, D379, G379 ENGINES Cooling System - (Radiator)
D399, G399, D398, G398, D379, G379 ENGINES Cooling System - (Heat Exchanger-Cooled)
D399, G399, D398, G398, D379, G379 ENGINES Cooling System - (Keel Cooling)
D399, G399, D398, G398, D379, G379 ENGINES Water Temperature Regulators
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.