PRODUCT SUPPORT PROGRAM FOR REPLACING THE REFRIGERANT COMPRESSOR ON DELAY TIMER ASSEMBLY (COMPRESSOR PROTECTION MODULE) ON CERTAIN D8T, D9T, D9R, D10R, D10T, D11R, AND D11T TRACK-TYPE TRACTORS Caterpillar

PRODUCT SUPPORT PROGRAM FOR REPLACING THE REFRIGERANT COMPRESSOR ON DELAY TIMER ASSEMBLY (COMPRESSOR PROTECTION MODULE) ON CERTAIN D8T, D9T, D9R, D10R, D10T, D11R, AND D11T TRACK-TYPE TRACTORS

Usage:

REBE6756-01

Show/hide table

25Jan2011

(Revised 09May2011)

U-30

A-22

D-30

O-30

Show/hide table

*After Failure Only*	PRODUCT SUPPORT PROGRAM FOR REPLACING THE REFRIGERANT COMPRESSOR ON DELAY TIMER ASSEMBLY (COMPRESSOR PROTECTION MODULE) ON CERTAIN D8T, D9T, D9R, D10R, D10T, D11R, AND D11T TRACK-TYPE TRACTORS
1808 1802 7320		PS51975

Show/hide table

NOTE:

This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS51975" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code.

Show/hide table

NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

Show/hide table


NOTE:	This Revised Service Letter replaces the 25Jan2011 Service Letter. Changes have been made to the Rework Procedure.

Show/hide table

TERMINATION DATE

31Jan2013

PROBLEM

Show/hide table

The existing 169-7443 ON Delay Timer assembly (Compressor Protection Module) for the refrigerant compressor can fail on certain D8T, D9T, D10T, D11T, D9R, D10R and D11R track-type tractors. If the existing compressor module fails, it can cause the air conditioning to not function correctly.

AFFECTED PRODUCT

Show/hide table

Model	Identification Number
D10R	3KR00744-01888 AKT00188-00943
D10T	RJG00003-00004, 105-2135
D11R	7PZ00286-01705, 50013, 75001-75025 9TR75002-75004
D11T	GEB00161-00609
D8T	J8B00204-01956, 2204-2353 KPZ00325-03338, 3500-3626
D9R	7TL00433-01409, 75001-75010 ABK00433-01098 ACL00655-01216, 75001, 75003 WDM00201-02300
D9T	RJS00118-01442

PARTS NEEDED

Show/hide table

Qty	Part Number	Description
2	7K1181	STRAP-CABLE
1	3442689	KIT-CONTROL GP
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 1% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table

1. Replace the existing compressor protection module with the new 338-1942 Compressor Protection Module included in the 344-2689 Kit.

2. Modify the existing harness with new gold pin contacts and connector (also in kit) to accept the new compressor protection module.

3. Change the harness routing for the compressor protection module.

Refer to the attached Rework Procedure for details.

Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table

Product smu/age whichever comes first	Caterpillar		Dealer Suggested		Customer Suggested
Product smu/age whichever comes first	Parts %	Labor Hrs%	Parts %	Labor Hrs%	Parts %	Labor Hrs%
0-5000 hrs, 0-48 mo	100.0%	100.0%	0.0%	0.0%	0.0%	0.0%

Show/hide table

NOTE: This is a 1.0-hour job

Show/hide table

PARTS DISPOSITION

Show/hide table

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

Rework Procedure

Show/hide table

1. Verify that the 169-7443 Control Group (Compressor Protection Module) is not operating correctly using Special Instruction REHS4499 "Testing the Refrigerant Compressor Protection Module."

2. After troubleshooting, turn the machine OFF.

3. Locate the compressor protection module. It should be located with the Air Conditioning Compressor. (Picture of typical location, may vary slightly depending on model)

Image1.3.1

4. Disconnect the electrical connection, remove the retaining bolt, and remove the compressor protection module.

5. Label the wires on the harness as 1, 2, 3, and 4 according to their position in the existing plug-connector.

6. Remove the plug-connector from the existing harness and cut the existing sockets off of the wires.

7. Strip each wire back and use a 239-5260 Crimper to install a 9X-3402 Socket onto each wire.

8. The wires still have the same numbering, but their relative position on the connector has changed. Install the new sockets into the new 230-5008 Plug-Connector in the following order:
Wire 1 from existing plug-connector (2) into position 1 on the new plug-connector (3).
Wire 2 from existing plug-connector (2) into position 2 on the new plug-connector (3).
Wire 3 from existing plug-connector (2) into position 3 on the new plug-connector (3).
Wire 4 from existing plug-connector (2) into position 4 on the new plug-connector (3).

NOTE: The sockets will "click" in the plug-connector when they are correctly installed. Ensure that they are correctly installed by then gently pulling on them and making sure they do not come out of the connector.

Image1.8.1

9. Install the new 338-1942 Compressor Protection Module with the existing bolt and plug in the electrical connectors. Push in red secondary lock to secure the connector. (Picture of typical location, may vary slightly depending on model)