INSTALLATION AND OPERATION LOAD SHARING MODULE Caterpillar


Electrostatic Discharge Awareness

Usage:

------ WARNING! ------

DANGER OF DEATH OR PERSONAL INJURY

WARNING-FOLLOW INSTRUCTIONS

Read this entire manual and all other publications pertaining to the work to be preformed before installing, operation, or servicing this equipment. Practice all plant and safety instructions and precautions. Failure to follow instructions can cause personal injury and/or property damage.

--------WARNING!------

------ WARNING! ------

WARNING-OVERSPEED PROTECTION

The engine, turbine, or other type of prime mover should be equipped with an overspeed shutdown device to protect against runaway or damage to the prime mover with possible personal injury, loss of life, or property damage.

The overspeed shutdown device must be totally independent of the prime mover control system. An overtemperature or overpressure shutdown device may also be needed for safety, as appropriate.

--------WARNING!------

------ WARNING! ------

WARNING-PROPER USE

Any unauthorized modifications to or use of this equipment outside its specified mechanical, electrical, or other operating limits may cause personal injury and/or property damage, including damage to the equipment. Any such unauthorized modifications: (i) constitute "misuse" and/or "negligence" within the meaning of the product warranty thereby excluding warranty coverage for any resulting damage, and (ii) invalidate product certifications or listings.

--------WARNING!------

------ WARNING! ------

CAUTION-POSSIBLE DAMAGE TO EQUIPMENT OR PROPERTY

CAUTION-BATTERY CHARGING

To prevent damage to a control system that uses an alternator or battery-charging device, make sure the charging device is turned off before disconnecting the battery from the system.

--------WARNING!------

------ WARNING! ------

CAUTION-ELECTROSTATIC DISCHARGE

Electronic controls contain static-sensitive parts. Observe the following precautions to prevent damage to these parts.

* Discharge body static before handling the control (with power to the control turned off, contact a grounded surface and maintain contact while handling the control).
* Avoid all plastic, vinyl, and Styrofoam (except antistatic versions) around circuit boards.
* Do not touch the components or conductors on a printed circuit board with your hands or with conductive devices.
--------WARNING!------

NOTE: IMPORTANT DEFINITIONS

* A WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
* A CAUTION indicates a potentially hazardous situation which, if not avoided, could result in damage to equipment or property.
* A NOTE provides other helpful information that does not fall under the warning or caution categories.

All electronic equipment is static-sensitive, some components more than others. To protect these components from static damage, you must take special precautions to minimize or eliminate electrostatic discharges.

Follow these precautions when working with or near the control.

1. Before doing maintenance on the electronic control, discharge the static electricity on your body to ground by touching and holding a grounded metal object (pipes, cabinets, equipment, etc.).
2. Avoid a build-up of static electricity on your body by not wearing clothing made of synthetic materials. Wear cotton or cotton-blend materials as much as possible because these do not store static electric charges as much as synthetics.
3. Keep plastic, vinyl, and Styrofoam materials (such as plastic or Styrofoam cups, cupholders, cigarette packages, cellophane wrappers, vinyl books or folders, plastic bottles, and plastic ashtrays) away from the control, the modules, and the work area as much as possible.
4. Do not remove the printed circuit board (PCB) from the control cabinet unless absolutely necessary. If you must remove the PCB from the control cabinet, follow these precautions:
* Do not touch any parts of the PCB except the edges.
* Do not touch the electrical conductors, the connectors, or the components with conductive devices or with your hands.
* When replacing a PCB, keep the new PCB in the plastic antistatic protective bag it comes in until you are ready to install it. Immediately after removing the old PCB from the control cabinet, place it in the antistatic protective bag.

------ WARNING! ------

CAUTION-ELECTROSTATIC DISCHARGE

To prevent damage to electronic components caused by improper handling, read and observe the precautions in Appendix B, Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, and Modules.

--------WARNING!------

Caterpillar Information System:

VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Service Partners
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Technical data
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Optional Spare Parts and Accessories
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Functional test
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Maintenance procedures
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Troubleshooting
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Operating instructions
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Commissioning
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Installation instructions
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Introduction and functional overview
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Declaration of Conformity
VISATRON OIL MIST DETECTORS VN115/87PLUS, VN116/87 PLUS, VN2 Safety instructions
INSTALLATION AND OPERATION LOAD SHARING MODULE Chapter 1 - General Information
INSTALLATION AND OPERATION LOAD SHARING MODULE Chapter 2 - Installation
INSTALLATION AND OPERATION LOAD SHARING MODULE Chapter 3 - Setup and Calibration
INSTALLATION AND OPERATION LOAD SHARING MODULE Chapter 4 - Theory Of Operation
INSTALLATION AND OPERATION LOAD SHARING MODULE Chapter 5 - Troubleshooting
INSTALLATION AND OPERATION LOAD SHARING MODULE Appendix A. - LSM Control Specifications
INSTALLATION AND OPERATION LOAD SHARING MODULE Appendix B. - Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, & Modules
INSTALLATION AND OPERATION LOAD SHARING MODULE Appendix C. - EMI Control in Electronic Governing Systems
CX28 On-Highway Transmission Electrical System 311-7810-01 CX28 On-Highway Transmission Electrical System 311-7810-01
CX35 On-highway Transmission Electrical System 311-6527-00 CX35 On-highway Transmission Electrical System 311-6527-00
TA22-M4WD Agricultural Tansmission Electrical System (Interactive) 291-4080 TA22-M4WD Agricultural Tansmission Electrical System (Interactive) 291-4080
TH48 - E70 Petroleum Transmission Electrical System (Interactive) 320-8181-01 TH48 - E70 Petroleum Transmission Electrical System (Interactive) 320-8181-01
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.