Fuel Pressure Sensor - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect harness assembly (1).
Show/hide table
Illustration 2 g06319303 - Remove fuel pressure sensor (2) from the fuel priming pump base.
- Remove the O-ring seal from fuel pressure sensor (2).
Show/hide table
| |
| Illustration 1 | g06319301 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install a new O-ring seal on fuel pressure sensor (2).
Show/hide table
Illustration 3 g06319303 - Install fuel pressure sensor (2) and tighten to a torque of
10 ± 2 N·m (89 ± 18 lb in) .Show/hide table
Illustration 4 g06319301 - Connect harness assembly (1).
Caterpillar Information System:
320D3 Hydraulic Excavator Engine Supplements Exhaust Elbow - Remove and Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Engine Mounted Oil Filtered Base
C175 Tier 4 Final Engines for Caterpillar Built Machines Fuel and Auxiliary Water Pump Drive - Remove and Install
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankcase Breather - Remove and Install
PM820, PM822, and PM825 Cold Planer Prepare the Machine for Maintenance
797F Tier 4 Off-Highway Truck Engine Supplement Pressure Sensor (Exhaust Inlet) - Remove and Install
New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620} New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620}
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490} Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
320D3 Hydraulic Excavator Machine Systems Bucket Linkage Bearings and Seals - Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Remote Mount
320D3 Hydraulic Excavator Machine Systems Bucket Linkage Bearings and Seals - Remove
A New Fuel Return Tube Assembly and Mounting Hardware is Now Used on Certain C9.3 Marine Engines {1274} A New Fuel Return Tube Assembly and Mounting Hardware is Now Used on Certain C9.3 Marine Engines {1274}
320D3 and 323D3 Excavators Machine System Specifications Final Drive
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Product Description
C18 Generator set and C18 Marine Engines Coolant Temperature Sensor - Remove and Install
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Prepare the Machine for Maintenance
C18 Generator set and C18 Marine Engines Electric Starting Motor - Remove and Install
G3500H Generator Set Engine Restriction of Air Inlet and Exhaust
C18 Generator set and C18 Marine Engines Electronic Control Module - Remove and Install
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankshaft Rear Seal - Remove and Install
C18 Generator set and C18 Marine Engines Vibration Damper and Pulley - Remove and Install
784C and 785C Off-Highway Truck/Tractors Machine Storage
A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057} A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057}
Software Update is Now Used on Certain 3500 Engines {1920} Software Update is Now Used on Certain 3500 Engines {1920}