Exhaust Elbow - Remove and Install
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Open hood (1).
Show/hide table
Illustration 2 g06319721 - Remove bolt (2). Loosen clamp (6) and disconnect hose (3) along with the clip.
- Loosen clamp (5). Remove exhaust elbow (4) and the O-ring seal.
Show/hide table
Illustration 1 | g06319720 |
- Install exhaust elbow (4) in the reverse order of removal.
- Tighten clamp (5) to a torque of
46 ± 2 N.m (34 ± 1 lb ft) .
- Tighten clamp (5) to a torque of
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Engine Mounted Oil Filtered Base
C175 Tier 4 Final Engines for Caterpillar Built Machines Fuel and Auxiliary Water Pump Drive - Remove and Install
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankcase Breather - Remove and Install
PM820, PM822, and PM825 Cold Planer Prepare the Machine for Maintenance
797F Tier 4 Off-Highway Truck Engine Supplement Pressure Sensor (Exhaust Inlet) - Remove and Install
New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620} New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620}
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490} Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
320D3 Hydraulic Excavator Machine Systems Bucket Linkage Bearings and Seals - Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Remote Mount
320D3 Hydraulic Excavator Machine Systems Bucket Linkage Bearings and Seals - Remove
A New Fuel Return Tube Assembly and Mounting Hardware is Now Used on Certain C9.3 Marine Engines {1274} A New Fuel Return Tube Assembly and Mounting Hardware is Now Used on Certain C9.3 Marine Engines {1274}
A New Engine Wiring Harness is Now Used for Certain C15 and C18 Tier 4 Final Engines {1403} A New Engine Wiring Harness is Now Used for Certain C15 and C18 Tier 4 Final Engines {1403}
C18 Generator set and C18 Marine Engines Fuel Pressure Sensor - Remove and Install
320D3 and 323D3 Excavators Machine System Specifications Final Drive
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Product Description
C18 Generator set and C18 Marine Engines Coolant Temperature Sensor - Remove and Install
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Prepare the Machine for Maintenance
C18 Generator set and C18 Marine Engines Electric Starting Motor - Remove and Install
G3500H Generator Set Engine Restriction of Air Inlet and Exhaust
C18 Generator set and C18 Marine Engines Electronic Control Module - Remove and Install
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankshaft Rear Seal - Remove and Install
C18 Generator set and C18 Marine Engines Vibration Damper and Pulley - Remove and Install
784C and 785C Off-Highway Truck/Tractors Machine Storage
A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057} A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057}