Bucket Linkage Bearings and Seals - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
C | 1P-0520 | Driver Gp | 1 |
D | 452-6006 | Molybdenum Grease | - |
Note: Refer to Specifications to identify the bucket families.
- Make sure that the bores in the power link and the bore in the stick are thoroughly clean and free of dirt and debris prior to the installation of the sleeve bearings.
Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.
Show/hide tableIllustration 1 g00698602 - Lower the temperature of sleeve bearings (5) that will be installed in the closed end of power link (2) to
−40 °C (−40 °F) . - Use Tooling (C) to install sleeve bearings (5) in the closed end of power link (2). Install the sleeve bearings until Dimension (X) is achieved. Dimension (X) should equal
9.5 ± 0.8 mm (0.374 ± 0.032 inch) .Show/hide tableIllustration 2 g00698673 - Lower the temperature of sleeve bearings (3) that will be installed in the open end of power link (2) to
−40 °C (−40 °F) . - Use Tooling (C) to install two sleeve bearings (3) in the open end of power link (2). Install the sleeve bearings until Dimension (Y) is achieved. Dimension (Y) should equal
9.2 ± 0.8 mm (0.362 ± 0.032 inch) .Show/hide tableIllustration 3 g00698265 - Apply a thin coat of Tooling (D) to lip seal (1). Use Tooling (C) to install lip seals (1) in power link (2). Install the lip seals with the sealing lip toward the outside of the bore.
Show/hide table
Illustration 4 g00698695 Show/hide tableIllustration 5 g00698698 View A-A - Lower the temperature of two sleeve bearings (6) that will be installed in the stick to
−40 °C (−40 °F) . - Use Tooling (C) to install sleeve bearings (6) in the stick. Install sleeve bearings (6) until Dimension (Z) is achieved. Dimension (Z) must be
9.50 ± 0.80 mm (0.374 ± 0.032 inch) .Show/hide tableIllustration 6 g00698407 - Apply a thin coat of Tooling (D) to lip seal (4). Install lip seals (4) in the stick. Install the lip seals with the sealing lip toward the outside of the bore.
Apply a thin coat of Tooling (D) to all sleeve bearings.
End By:
- Install the bucket linkage.
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Remote Mount
320D3 Hydraulic Excavator Machine Systems Bucket Linkage Bearings and Seals - Remove
A New Fuel Return Tube Assembly and Mounting Hardware is Now Used on Certain C9.3 Marine Engines {1274} A New Fuel Return Tube Assembly and Mounting Hardware is Now Used on Certain C9.3 Marine Engines {1274}
A New Engine Wiring Harness is Now Used for Certain C15 and C18 Tier 4 Final Engines {1403} A New Engine Wiring Harness is Now Used for Certain C15 and C18 Tier 4 Final Engines {1403}
A New Engine Wiring Harness is Now Used for Certain C15 and C18 Tier 4 Final Machine Engines {1403} A New Engine Wiring Harness is Now Used for Certain C15 and C18 Tier 4 Final Machine Engines {1403}
Outboard Bearing Removal Procedure for Integrated Throttle Body (ITB) on Certain 3500 Engines {1269} Outboard Bearing Removal Procedure for Integrated Throttle Body (ITB) on Certain 3500 Engines {1269}
New Non-Contact Switch is Now Used on Certain 3500Engines {1078, 1408, 5736, 7400} New Non-Contact Switch is Now Used on Certain 3500Engines {1078, 1408, 5736, 7400}
797F Tier 4 Off-Highway Truck Engine Supplement Temperature Sensor (Exhaust Inlet) - Remove and Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Remove - Remote Mount
320D3 Hydraulic Excavator Machine Systems Duo-Cone Conventional Seals - Install
PM820, PM822, and PM825 Cold Planer Conveyor Belt Tension and Tracking - Adjust
320D3 Hydraulic Excavator Machine Systems Pump Drive Coupling - Remove and Install
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490} Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620} New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620}
797F Tier 4 Off-Highway Truck Engine Supplement Pressure Sensor (Exhaust Inlet) - Remove and Install
PM820, PM822, and PM825 Cold Planer Prepare the Machine for Maintenance
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankcase Breather - Remove and Install
C175 Tier 4 Final Engines for Caterpillar Built Machines Fuel and Auxiliary Water Pump Drive - Remove and Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Engine Mounted Oil Filtered Base
320D3 Hydraulic Excavator Engine Supplements Exhaust Elbow - Remove and Install
C18 Generator set and C18 Marine Engines Fuel Pressure Sensor - Remove and Install
320D3 and 323D3 Excavators Machine System Specifications Final Drive
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Product Description
C18 Generator set and C18 Marine Engines Coolant Temperature Sensor - Remove and Install