Fuel System Primary Filter (Water Separator) Element - Replace
Show/hide table
注意事項 |
---|
在檢驗、保養、測試、調整及修理產品時,請小心確保油液有容器盛裝。 在打開任何艙室或拆卸任何含有用液的組件前,應準備好盛裝用液的適當容器。 請參閱特別出版品, N4NG2500, "代理商維修工具目錄",以瞭解適合用來收集及容納 Cat® 產品之液體的工具和耗材。 按照當地的條例和法規棄置廢棄的油液。 |
Show/hide table
注意事項 |
---|
安裝燃油濾清器前,請勿在其內加注燃油。 這些燃油不會經過過濾且可能會受到汙染。 受到汙染的燃油會導致燃油系統零件加速磨損。 在啟動引擎前,燃油系統必須加注燃油。 |
Show/hide table
插圖 1 | g06311601 |
(序號 SL8) (序號 TLZ) (序號 ESE) (1) 濾清器外殼 (2) 排放閥 |
Show/hide table
插圖 2 | g06311603 |
(序號 JB7) (序號 HN8) (序號 HC8) (1) 濾清器外殼 (2) 排放閥 |
- 打開右側檢修門。
- 打開濾清器外殼 (1) 底部的排放閥 (2)。 讓水和燃油排入適當的容器內。
- 使用帶式扳手從安裝基座拆下濾清器外殼 (1)。
- 從濾清器外殼取下舊的濾清器。 丟棄舊的濾清器。
- 清潔濾清器外殼,然後將新的濾清器濾芯裝入外殼。
- 將濾清器外殼裝回安裝基座。
- 關閉排放閥 (2)。
- 灌注燃油系統。
偏好設定: 如需正確的操作步驟,請參閱操作與維護手冊, "燃油系統 - 注油"。
- 關閉右側檢修門。
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Fuel System Secondary Filter - Replace
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Hydraulic Cylinder
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Hydraulic Cylinder
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Multi-Processor Hydraulic System
New Procedure for Power Cycle is Now Available for Certain Cat® Product Link (PL131) Devices {7606} New Procedure for Power Cycle is Now Available for Certain Cat® Product Link (PL131) Devices {7606}
Improved Product Link On-Board Software is Now Available for All Cat® Products {7606} Improved Product Link On-Board Software is Now Available for All Cat® Products {7606}
An Improved Rear Wheel Bearing for Certain Large Off-Highway Trucks is Available {4008, 7551} An Improved Rear Wheel Bearing for Certain Large Off-Highway Trucks is Available {4008, 7551}
The Housing Assembly for the Front Suspension Group May Crack on Certain 773G and 775G Off-Highway Trucks {7200, 7201} The Housing Assembly for the Front Suspension Group May Crack on Certain 773G and 775G Off-Highway Trucks {7200, 7201}
The Pressure Setting on the Hoist Raise Valve Group May Be Low on Certain Off-Highway Trucks {5051, 5069, 5117} The Pressure Setting on the Hoist Raise Valve Group May Be Low on Certain Off-Highway Trucks {5051, 5069, 5117}
New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202} New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202}
New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202} New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202}
Improved Engine Software and Diesel Exhaust Fluid Injector Assembly Is Now Used on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {108I, 7610, 7620} Improved Engine Software and Diesel Exhaust Fluid Injector Assembly Is Now Used on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {108I, 7610, 7620}
New Software Updates are Now Available for Certain 773E and 777E Off-Highway Trucks {7490, 7610, 7620} New Software Updates are Now Available for Certain 773E and 777E Off-Highway Trucks {7490, 7610, 7620}
An Improved Stub Shaft is now Used for the CX38 Transmission in Certain 700 Series Articulated Trucks {3063, 3160} An Improved Stub Shaft is now Used for the CX38 Transmission in Certain 700 Series Articulated Trucks {3063, 3160}
966M XE and 972M XE Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Hydraulic Oil Cooler - Lines
PM820, PM822, and PM825 Cold Planer Air Pressure Regulator
PM820, PM822, and PM825 Cold Planer Engine Crankcase Breather - Clean
24 Motor Grader Systems Piston Pump (Implement)
994K Wheel Loader Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Inlet Nitrogen Oxide Sensor 1
24 Motor Grader Systems Pump Control Operation
24 Motor Grader Systems Control Manifold (Implements)
24 Motor Grader Systems Shutoff Valve
C175 Tier 4 Final Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
24 Motor Grader Systems Blade Cushion