Air Inlet Manifold - Remove and Install
Note: Use appropriate caps and plugs on all fittings to prevent contamination.
Note: Inspect all O-rings, gaskets, and seals for wear and damage. Replace if necessary.
- Remove hose clamp (1), two bolts (3), and tube assembly (2).
Show/hide table
Illustration 2 g06311389 - Remove all necessary mounting hardware (4).
- Disconnect harness (5) and position out of the way.
- Disconnect sensors (6), and (7), and atomizer (8) and position out of the way.
Show/hide table
Illustration 3 g06311394 - Remove eight bolts (9) and manifold (10).
- Repeat steps 1 - 5 for the remaining inlet manifolds.
- Repeat steps 1 - 6 on the opposite side.
Show/hide table
| |
| Illustration 1 | g06310913 |
|
Repeat for each tube assembly. | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty. |
| A | 207-1601 | Rubber Lubricant | - |
- Install the air inlet manifold in reverse order of removal.
- Install pressure sensor (exhaust inlet) (6). Refer to Disassembly and Assembly, "Pressure Sensor (Exhaust Inlet) - Remove and Install".
- Install temperature sensor (exhaust inlet) (7). Refer to Disassembly and Assembly, "Temperature Sensor (Exhaust Inlet) - Remove and Install".
- Lubricate the inside diameter of the T-joint with Tooling (A) when installing tube assembly (2).
Caterpillar Information System:
320D3 Hydraulic Excavator Machine Systems Bucket Cylinder - Assemble
323D3 Hydraulic Excavators Engine Supplements Turbocharger - Remove and Install
323D3 Hydraulic Excavators Engine Supplements Valve Mechanism Cover - Remove and Install
320D3 Hydraulic Excavator Machine Systems Bucket Cylinder - Disassemble
320D3 Excavators Boom/Stick/Bucket Combinations
323D3 Hydraulic Excavators Engine Supplements Crankshaft Front Seal - Remove and Install
320D3 and 323D3 Excavators Systems Main Hydraulic System
323D3 Hydraulic Excavators Engine Supplements Water Pump - Remove and Install
320D3 Hydraulic Excavator Machine Systems Load Control Valve (Stick Cylinder) - Assemble
320D3 Hydraulic Excavator Machine Systems Storage Box and Covers (Cab) - Remove and Install
320D3 Hydraulic Excavator Machine Systems Seat - Remove and Install
797F Tier 4 Off-Highway Truck Engine Supplement Clean Emissions Module - Remove and Install
The Buffer Seal Assembly in the Steering Cylinder Group May Wear Prematurely on Certain 773G, 775G, and 777G Off-Highway Trucks {4303, 7555} The Buffer Seal Assembly in the Steering Cylinder Group May Wear Prematurely on Certain 773G, 775G, and 777G Off-Highway Trucks {4303, 7555}
Rework Procedure for New Voltage Selector Switch Cable Routing Now Used on Certain XQ35 and XQ60 Generator Sets {1410} Rework Procedure for New Voltage Selector Switch Cable Routing Now Used on Certain XQ35 and XQ60 Generator Sets {1410}
The 293-4388 Clamp As May Break on Certain 3500 Series Engines {1051, 1054} The 293-4388 Clamp As May Break on Certain 3500 Series Engines {1051, 1054}
New Engine Software is Now Used on Certain C9 Industrial Engines {1920} New Engine Software is Now Used on Certain C9 Industrial Engines {1920}
320D3 and 323D3 Excavators Systems Relief Valve (Main)
320D3 Excavators Leaving the Machine
320D3 Excavators Securing the Machine
320D3 Excavators Lifting and Tying Down the Machine
New Software Updates Are Now Used On Certain C9.3 through C18 Engines {1920} New Software Updates Are Now Used On Certain C9.3 through C18 Engines {1920}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Restricted Visibility
New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202} New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202}
New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202} New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202}