Unit Injector Hydraulic Pump
Show/hide table
Illustration 1 | g06310731 |
Show/hide table
Illustration 2 | g06310773 |
Section B-B |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | 8 | 218-8655 Bolt | Use the following procedure to tighten the bolt using torque-turn method:
1. Tighten to SAS (Start Angle Snug) 2. Rotate the fasteners to 24 ± 2 degrees. 3. Final minimum torque to |
Use the following procedure to tighten the bolt using torque method:
Torque to |
|||
2 | 3 | 228-5897 Bolt | Use the following procedure to tighten the bolt using torque-turn method:
1. Tighten to SAS (Start Angle Snug) 2. Rotate the fasteners to 81 ± 2 degrees. 3. Final minimum torque to |
Use the following procedure to tighten the bolt using torque method:
Torque to |
|||
3 | 3 | 313-4620 Screw | Use the following procedure to tighten the screw using torque-turn method:
1. Tighten to SAS (Start Angle Snug) 2. Rotate the fasteners to 30 ± 1 degrees. 3. Final minimum torque to |
Use the following procedure to tighten the screw using torque method:
Torque to |
|||
4 | 1 | 153-7036 Spool | Install the cartridge until fully seated against the shoulder of block. |
Install retainer until fully seated against cartridge to eliminate endplay. | |||
5 | 3 | 179-1218 Bolt | Use the following procedure to tighten the bolt using torque method:
Torque to |
6 | 1 | 8C-6711 Retainer Nut | Use the following procedure to tighten the nut using torque method:
Torque to |
7 | 1 | 5C-2890 Nut | Use the following procedure to tighten the nut using torque method:
Torque to |
8 | - | - | Install the bearing so that end with the bearing ident number is oriented as shown in Illustration 2. |
Press the bearing into bore of barrel to the depth (J) of |
|||
9 | 1 | 1N-8062 Needle Bearing As | Install the bearing so that end with the bearing ident number is oriented as shown in Illustration 2. |
Press the bearing into bore of barrel to the depth (K) of |
|||
G | - | - | Press pin into block to obtain pin protrusion length of |
H | - | - | Press pin into block to obtain pin protrusion length of |
- | - | - | At 3300 rpm, minimum flow at |
- | - | - | At 3300 rpm, relief valve minimum VOP should be |
Caterpillar Information System:
An Improved Wheel Speed Sensor is Now Available on Certain RM500B Rotary Mixers {4351, 5058} An Improved Wheel Speed Sensor is Now Available on Certain RM500B Rotary Mixers {4351, 5058}
Cleaning Procedure for the Polycarbonate Windshields, Windows, and Skylights on Certain Forest Machines, Track Feller Bunchers, Wheel Feller Bunchers, and Wheel Skidders {7310, 7340} Cleaning Procedure for the Polycarbonate Windshields, Windows, and Skylights on Certain Forest Machines, Track Feller Bunchers, Wheel Feller Bunchers, and Wheel Skidders {7310, 7340}
Slow or Inoperable Telescoping Cylinder During Retraction on Certain Telehandlers {5325, 5362} Slow or Inoperable Telescoping Cylinder During Retraction on Certain Telehandlers {5325, 5362}
Certain Cat® Product Link Device Back-Office May Not Allow to Set Hours Locally {7606} Certain Cat® Product Link Device Back-Office May Not Allow to Set Hours Locally {7606}
Ethernet Flashing and Programming Routers on Cat® Command for Dozing System Devices {7610, 7620} Ethernet Flashing and Programming Routers on Cat® Command for Dozing System Devices {7610, 7620}
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Fuel Rail Pressure Problem - Gas
Hose Clamps May Have the Incorrect Torque on Certain Telehandlers {1380, 1812, 1813, 5057} Hose Clamps May Have the Incorrect Torque on Certain Telehandlers {1380, 1812, 1813, 5057}
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Steering Cylinder (Rear) - Remove and Install
An Improved Pin is Now Used for Certain CX38 Transmission in Certain 700 Series Articulated Trucks {3160} An Improved Pin is Now Used for Certain CX38 Transmission in Certain 700 Series Articulated Trucks {3160}
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Fuel System Operation
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending General Information (Fuel System) - Gas
2570C and 2670C Wheel Feller Bunchers Cab Tilting
3516E Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install - With Fuel/Water Separator
C175 Tier 4 Final Engines for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
Shims Added to Coupler to Decrease Side to Side Motion Are Now Used on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {6129, 7000} Shims Added to Coupler to Decrease Side to Side Motion Are Now Used on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {6129, 7000}
The Buffer Seal Assembly in the Steering Cylinder Group May Wear Prematurely on Certain 773G, 775G, and 777G Off-Highway Trucks {4303, 7555} The Buffer Seal Assembly in the Steering Cylinder Group May Wear Prematurely on Certain 773G, 775G, and 777G Off-Highway Trucks {4303, 7555}
Troubleshooting Procedures for Supercom Data Acquisition Systems are Now Available for Certain Off-Highway Trucks {7600, 7601, 7606, 7620} Troubleshooting Procedures for Supercom Data Acquisition Systems are Now Available for Certain Off-Highway Trucks {7600, 7601, 7606, 7620}
New C175 High Altitude Low Maintenance Ratio Engine for 797 Off-Highway Trucks {1000} New C175 High Altitude Low Maintenance Ratio Engine for 797 Off-Highway Trucks {1000}
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Control Manifold
A New Thermowell Is Available for Certain C175 Off-Highway Truck/Tractor Engines {7498} A New Thermowell Is Available for Certain C175 Off-Highway Truck/Tractor Engines {7498}
Oil Fill Capacity for the Circle Drive Housing has been Updated on Certain 14M Series 3 Motor Graders {0374, 5207} Oil Fill Capacity for the Circle Drive Housing has been Updated on Certain 14M Series 3 Motor Graders {0374, 5207}
Product Link ® Elite PLE742 Systems Service Tools
563D and 573D Wheel Feller Buncher Windows - Clean