Service Brake (Wheel Spindle) - Remove and Install
Start By:
- Remove the fenders.
- Remove the drive chain.
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 132-5136 | Lift Bracket As | 1 |
| B | 154-6185 | Forcing Bolt | 2 |
| C | - | Loctite 272 | - |
- Remove two bolts (1), the washers, and cover (2). Disconnect hose assemblies (3) and (4) and remove the O-ring seals.
Show/hide table
Illustration 2 g06343341 - Remove bolts (5) and the washers. Leave 2 bolts (5) installed at Locations (X).
Show/hide table
Illustration 3 g06343352 - Install Tooling (A) and attach a suitable lifting device to service brake assembly (6). The weight of service brake assembly (6) is approximately
975 kg (2150 lb) .Show/hide table
Illustration 4 g06343397 - Remove 2 remaining bolts (5). Install tooling (B) at 2 Locations (Y). Use Tooling (B) to remove service brake assembly (6).
Show/hide table
| |
| Illustration 1 | g06343256 |
- Install service brake assembly (6) in the reverse order of removal.
- Apply Tooling (C) to the threads of bolts (5).
Caterpillar Information System:
BD118 and BD121 Side Discharge Bucket Conveyor Belt Tension and Tracking - Adjust
BD118 and BD121 Side Discharge Bucket Bearings - Lubricate
Joystick Control Assembly May Malfunction on Certain Telehandlers {5063, 5705} Joystick Control Assembly May Malfunction on Certain Telehandlers {5063, 5705}
Proximity Sensor on the Stabilizer Legs May Become Open Circuit on Certain Telehandlers {1408, 7222, 7332} Proximity Sensor on the Stabilizer Legs May Become Open Circuit on Certain Telehandlers {1408, 7222, 7332}
MD6200 Rotary Drill Prepare the Machine for Maintenance
24 Motor Grader Drawbar Ball and Socket End Play - Check/Adjust
C9.3 Engine for Caterpillar Built Machines Fuel Transfer Pump
Snow Push and Plows Work Tool Supplement Springs - Inspect/Replace
2D GRADE System for 24 Next Gen Motor Graders Electrical Power Supply - Test
Snow Push and Plows Work Tool Supplement Side Plate Skid Plate - Inspect/Replace
Snow Push and Plows Work Tool Supplement Plate Locations and Film Locations
Check the Lower ROPS Mount on R2900G and R3000H Load Haul Dump Machines {7266} Check the Lower ROPS Mount on R2900G and R3000H Load Haul Dump Machines {7266}
New Rework Procedure Now Used for the Engine Wiring Harness on Certain 793D Off-Highway Trucks to Allow Air Conditioning to Function {1408} New Rework Procedure Now Used for the Engine Wiring Harness on Certain 793D Off-Highway Trucks to Allow Air Conditioning to Function {1408}
3516E Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
New Primary Isolation Mount Assemblies Now Used on Certain 797F Off-Highway Truck Engines {1901} New Primary Isolation Mount Assemblies Now Used on Certain 797F Off-Highway Truck Engines {1901}
24 Motor Grader Systems Hydraulic Tank
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending General Information (Fuel System) - Gas
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Fuel System Operation
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
An Improved Pin is Now Used for Certain CX38 Transmission in Certain 700 Series Articulated Trucks {3160} An Improved Pin is Now Used for Certain CX38 Transmission in Certain 700 Series Articulated Trucks {3160}
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Steering Cylinder (Rear) - Remove and Install
Hose Clamps May Have the Incorrect Torque on Certain Telehandlers {1380, 1812, 1813, 5057} Hose Clamps May Have the Incorrect Torque on Certain Telehandlers {1380, 1812, 1813, 5057}
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Fuel Rail Pressure Problem - Gas
Ethernet Flashing and Programming Routers on Cat® Command for Dozing System Devices {7610, 7620} Ethernet Flashing and Programming Routers on Cat® Command for Dozing System Devices {7610, 7620}