Joystick Control Assembly May Malfunction on Certain Telehandlers {5063, 5705} Caterpillar


Joystick Control Assembly May Malfunction on Certain Telehandlers {5063, 5705}

Usage:

TH514D MWG
Telehandler
TH3510D (S/N: TH21-UP)
TH357D (S/N: TD61-UP)
TH408D (S/N: TH91-UP)
TH514D (S/N: MWG1-UP)

Introduction

The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.

Problem

Joystick control assembly may malfunction on the machines listed above. The malfunction of the joystick control assembly machine may prevent the machine from starting. The display may show an error code 666-1 and the operator may experience a loss of hydraulic function.

Solution



Illustration 1g06311091
541-7470 Joystick Control As

If the joystick control assembly malfunctions, replace the 541-7470 Joystick Control As with the same part number.

Report the failure through CPI feedback tool in Service Information Management System (SIMSi) referencing CPI number 415513 to have a "Send-It-Back" (SIB) request generated. A SIB request will be issued to your dealer code in the SIB system after the (SIMSi) entry is created.

Submit the failed component along with any other available information to (SIMSi).

Caterpillar Information System:

Proximity Sensor on the Stabilizer Legs May Become Open Circuit on Certain Telehandlers {1408, 7222, 7332} Proximity Sensor on the Stabilizer Legs May Become Open Circuit on Certain Telehandlers {1408, 7222, 7332}
MD6200 Rotary Drill Prepare the Machine for Maintenance
24 Motor Grader Drawbar Ball and Socket End Play - Check/Adjust
C9.3 Engine for Caterpillar Built Machines Fuel Transfer Pump
Snow Push and Plows Work Tool Supplement Springs - Inspect/Replace
2D GRADE System for 24 Next Gen Motor Graders Electrical Power Supply - Test
Snow Push and Plows Work Tool Supplement Side Plate Skid Plate - Inspect/Replace
Snow Push and Plows Work Tool Supplement Plate Locations and Film Locations
Check the Lower ROPS Mount on R2900G and R3000H Load Haul Dump Machines {7266} Check the Lower ROPS Mount on R2900G and R3000H Load Haul Dump Machines {7266}
The Heater Control Group in the Air Conditioning Group May Fail on Certain 773E and 777E Off-Highway Trucks {7304} The Heater Control Group in the Air Conditioning Group May Fail on Certain 773E and 777E Off-Highway Trucks {7304}
A Hose Clamp May Fail in the Heater Lines Group on Certain 770G, 772G, 773G, 775G, and 777G Off-Highway Trucks {1380, 1808, 1812, 7304} A Hose Clamp May Fail in the Heater Lines Group on Certain 770G, 772G, 773G, 775G, and 777G Off-Highway Trucks {1380, 1808, 1812, 7304}
24 Motor Grader Systems Oil Filter (Hydraulic Return)
BD118 and BD121 Side Discharge Bucket Bearings - Lubricate
BD118 and BD121 Side Discharge Bucket Conveyor Belt Tension and Tracking - Adjust
24 Motor Grader Power Train Service Brake (Wheel Spindle) - Remove and Install
New Rework Procedure Now Used for the Engine Wiring Harness on Certain 793D Off-Highway Trucks to Allow Air Conditioning to Function {1408} New Rework Procedure Now Used for the Engine Wiring Harness on Certain 793D Off-Highway Trucks to Allow Air Conditioning to Function {1408}
3516E Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
New Primary Isolation Mount Assemblies Now Used on Certain 797F Off-Highway Truck Engines {1901} New Primary Isolation Mount Assemblies Now Used on Certain 797F Off-Highway Truck Engines {1901}
24 Motor Grader Systems Hydraulic Tank
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending General Information (Fuel System) - Gas
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Fuel System Operation
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
An Improved Pin is Now Used for Certain CX38 Transmission in Certain 700 Series Articulated Trucks {3160} An Improved Pin is Now Used for Certain CX38 Transmission in Certain 700 Series Articulated Trucks {3160}
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Steering Cylinder (Rear) - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.