Nitrogen Oxide Sensor - Remove and Install - Inlet
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 468-8116 | Socket | 1 |
B | - | Loctite Nickel Anti-Seize Compound | 1 |
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Turn the battery disconnect switch to the OFF position.
Show/hide table
Illustration 1 g06132078 - Open door assembly (1).
Show/hide table
Illustration 2 g06132116 - Cut the cable strap and use Tooling (A) to disconnect nitrogen oxide sensor (2).
Show/hide table
Illustration 3 g06132126 - Cut the cable strap and disconnect harness assembly (3).
- Remove bolts (4) and nitrogen oxide sensor (2).
- Install nitrogen oxide sensor (2) in the reverse order of removal.
- Apply Tooling (B) to the threads of nitrogen oxide sensor (2).
Note: If a new nitrogen oxide sensor is being installed, do not apply Tooling (B) to the threads. New nitrogen oxide sensors should have the required lubricant already on the threads.
- Use Tooling (A) to tighten nitrogen oxide sensor (2) to a torque of
50 ± 10 N·m (37 ± 7 lb ft) .
- Apply Tooling (B) to the threads of nitrogen oxide sensor (2).
Caterpillar Information System:
An Improved Inner Clutch Seal is Now Available For Certain 700 C-Series Articulated Trucks {3030, 3160} An Improved Inner Clutch Seal is Now Available For Certain 700 C-Series Articulated Trucks {3030, 3160}
773E Off-Highway Truck Air System and Brakes Air Compressor and Governor - Test and Adjust
New Gear Assemblies in the Transmission Pump Are Now Used on Certain 793F Off-Highway Trucks {3108, 5073} New Gear Assemblies in the Transmission Pump Are Now Used on Certain 793F Off-Highway Trucks {3108, 5073}
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Engine Supplement Muffler - Remove and Install
A New Felling Head Limiter Crack Repair Is Now Available for Certain Felling Heads {6712} A New Felling Head Limiter Crack Repair Is Now Available for Certain Felling Heads {6712}
Felling Head Limiter Crack Repair Procedure {6712} Felling Head Limiter Crack Repair Procedure {6712}
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Engine Supplement Water Separator and Fuel Filter (Primary) - Remove and Install
990K Wheel Loader Systems Steering Control Group
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Air Cleaner Dust Valve - Clean/Inspect
416F2, 420F2 and 430F2 Backhoe Loaders Engine Air Filter Primary Element - Clean/Replace
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Transmission Oil Filter - Replace
980L Tier 3 Wheel Loader Machine System Loader Frame to Rear Frame - Connect
M325D MH Material Handler Axle Oil Sample - Obtain
2570D and 2670D Wheel Feller Buncher Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Outlet
CCS9 Combination Vibratory Compactor Propel Systems General Information (Propel System)
CCS9 Combination Vibratory Compactor Propel Systems Operator Controls (Propel System)
CCS9 Combination Vibratory Compactor Propel Systems Propel System Components
CCS9 Combination Vibratory Compactor Propel Systems Piston Pump (Propel)
3512E Tier 4 Final Engines for 785G Off-Highway Trucks Coolant Level Is Low
CCS9 Combination Vibratory Compactor Propel Systems Piston Motor (Wheel Propel)
CCS9 Combination Vibratory Compactor Propel Systems Piston Motor (Drum Propel)
CCS9 Combination Vibratory Compactor Propel Systems Hydraulic Schematic (Propel System)
CCS9 Combination Vibratory Compactor Machine Systems General Information (Vibratory System)
Front Axle Pin May Break on Certain 424B Backhoe Loaders {3282, 7000} Front Axle Pin May Break on Certain 424B Backhoe Loaders {3282, 7000}