Muffler - Remove and Install
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Open the hood. Engage the hood support.
- Turn the battery disconnect switch to the OFF position.
Show/hide table
Illustration 1 g06132035 - Loosen clamp (2) that secures the exhaust tube to muffler (1).
Show/hide table
Illustration 2 g06132039 - Loosen clamp (4) that secures the exhaust tube to muffler (1).
- Loosen two clamps (3) and remove muffler (1).
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Loctite 243 | 1 |
- Install muffler (1) in the reverse order of removal.
- Orient the opening on clamps (4) and (2) 90 degrees from the slots in muffler (1).
- Apply Tooling (A) the bolts on clamps (4) and (2).
- Tighten clamp (4) to a torque of
20 ± 2 N·m (177 ± 18 lb in) . - Tighten two clamps (3) to a torque of
9 ± 1 N·m (80 ± 9 lb in) . - Tighten clamp (2) to a torque of
20 ± 2 N·m (177 ± 18 lb in) .
Caterpillar Information System:
A New Felling Head Limiter Crack Repair Is Now Available for Certain Felling Heads {6712} A New Felling Head Limiter Crack Repair Is Now Available for Certain Felling Heads {6712}
Felling Head Limiter Crack Repair Procedure {6712} Felling Head Limiter Crack Repair Procedure {6712}
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Engine Supplement Water Separator and Fuel Filter (Primary) - Remove and Install
990K Wheel Loader Systems Steering Control Group
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Air Cleaner Dust Valve - Clean/Inspect
416F2, 420F2 and 430F2 Backhoe Loaders Engine Air Filter Primary Element - Clean/Replace
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Transmission Oil Filter - Replace
980L Tier 3 Wheel Loader Machine System Loader Frame to Rear Frame - Connect
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Lift and Tilt Cylinder Speed - Check
793D Off-Highway Truck Power Train Drive Shaft (Main)
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager System Schematic
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Calibration Using Electronic Service Tool
New Gear Assemblies in the Transmission Pump Are Now Used on Certain 793F Off-Highway Trucks {3108, 5073} New Gear Assemblies in the Transmission Pump Are Now Used on Certain 793F Off-Highway Trucks {3108, 5073}
773E Off-Highway Truck Air System and Brakes Air Compressor and Governor - Test and Adjust
An Improved Inner Clutch Seal is Now Available For Certain 700 C-Series Articulated Trucks {3030, 3160} An Improved Inner Clutch Seal is Now Available For Certain 700 C-Series Articulated Trucks {3030, 3160}
2570D and 2670D Wheel Feller Buncher Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Inlet
M325D MH Material Handler Axle Oil Sample - Obtain
2570D and 2670D Wheel Feller Buncher Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Outlet
CCS9 Combination Vibratory Compactor Propel Systems General Information (Propel System)
CCS9 Combination Vibratory Compactor Propel Systems Operator Controls (Propel System)
CCS9 Combination Vibratory Compactor Propel Systems Propel System Components
CCS9 Combination Vibratory Compactor Propel Systems Piston Pump (Propel)
3512E Tier 4 Final Engines for 785G Off-Highway Trucks Coolant Level Is Low
CCS9 Combination Vibratory Compactor Propel Systems Piston Motor (Wheel Propel)