Engine Oil Filter and Oil Filter Base - Remove and Install
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 185-3630 | Strap Wrench As | 1 |
Show/hide table
 |
|
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Open the hood and remove the left side engine panel.
Show/hide table
Illustration 1 g06375047 - Drain the engine Oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures.
- Disconnect hose assembly (1). Use Tooling (A) to remove engine oil filter (2). Remove engine oil filter (2).
Show/hide table
Illustration 2 g06375050 - Remove bolts (3), bolts (6), bolts (5), and filter base (4).
- Remove tube assembly (7) and the O-ring seal from filter base (4).
- Install filter base (4) and engine oil filter (2) in the reverse order of removal.
- Lubricate the bore for the O-ring seal of tube assembly (7) lightly with the lubricant that is being sealed.
- Use the following procedure to tighten engine oil filter (2):
- Lubricate the seal and bore of engine oil filter (2) lightly with the lubricant that is being sealed. Install engine oil filter (2) in vertical orientation only.
- Tighten engine oil filter (2) to a torque of
100 ± 5 N.m (74 ± 4 lb ft) . - Ensure that there is no gap between engine oil filter (2) and filter base (4).
Caterpillar Information System:
C7.1 Engines and Generator Sets Exhaust System Contains Fuel
C7.1 Engines and Generator Sets Exhaust System Contains Coolant
CB7, CB8 and CB10 Vibratory Asphalt Compactors Power Train Drum Mounting
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
994K Wheel Loader Machine Systems Seat - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Pilot Pressure - Test and Adjust
A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802} A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802}
Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304} Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304}
Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065} Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065}
2570D and 2670D Wheel Feller Buncher Engine Supplement Fan - Remove and Install
A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282} A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282}
Installation of the 519-9196 Lines Gp - Coupler on Certain Backhoe Loaders {5057, 5133, 6129} Installation of the 519-9196 Lines Gp - Coupler on Certain Backhoe Loaders {5057, 5133, 6129}
C7.1 Engines and Generator Sets Exhaust System Contains Oil
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380} Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380}
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
MH3037 Material Handler Machine Systems Main Control Valve - Remove and Install - Lower Valve
C7.1 Engines and Generator Sets Fuel Contains Water
2570D and 2670D Wheel Feller Buncher Engine Supplement Piston Motor (Fan) - Remove and Install
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
C7.1 Engines and Generator Sets Fuel Temperature Is High
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble
C7.1 Engines and Generator Sets Inlet Air Is Restricted
980L Tier 3 Wheel Loader Engine Supplement Expansion Tank - Remove and Install