Exhaust System Contains Coolant
Use the following procedure to troubleshoot a problem with coolant in the exhaust system.
- NOx Reduction System (NRS) cooler
- Cylinder head gasket
- Cylinder head
- Cylinder block
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. NRS cooler A. Check the NRS cooler for leaks for utilizing the "On Engine Test Procedure". Refer to Systems Operation, Testing, and Adjusting, "Exhaust Cooler (NRS) - Test". |
NRS cooler |
Result : The NRS cooler has a leak. Repair: Replace the NRS cooler. Refer to the Disassembly and Assembly manual for the correct procedure. Result : The NRS cooler does not have a leak. Proceed to Test Step 2. |
2. Cylinder head gasket leak A. Check the cylinder head gasket for leaks. |
Cylinder head gasket |
Result : The cylinder head gasket is leaking. Proceed to Test Step 3. Result : The cylinder head gasket is not leaking. Proceed to Test Step 3. |
3. Cylinder head A. Check for cracks in the cylinder head. Perform a leak test on the cylinder head. Refer to the Systems Operation, Testing, and Adjusting, "Cylinder Head - Inspect" for the correct procedure. |
Cylinder head |
Result : A crack is found in the cylinder head. Repair: Repair the cylinder head or replace the cylinder head. Refer to the Disassembly and Assembly manual. Proceed to Test Step 4. Result : The cylinder head is OK. Proceed to Test Step 4. |
4. Cylinder Block A. Check for cracks in top face of the cylinder block. Refer to the Systems Operation, Testing, and Adjusting, "Cylinder Block - Inspect" for the correct procedure. |
Cylinder head |
Result : A crack is found in the cylinder block. Repair: Repair the cylinder block or replace the cylinder block. Refer to the Disassembly and Assembly manual. Repair: Assemble the cylinder head with a new cylinder head gasket. Refer to the Disassembly and Assembly manual. Result : The cylinder block is OK. Repair: Assemble the cylinder head with a new cylinder head gasket. Refer to the Disassembly and Assembly manual. |
Caterpillar Information System:
C175 Oil&Gas Offshore Engine Solenoid Valve - Test - Engine
C175 Oil&Gas Offshore Engine Data Link - Test
C175 Oil&Gas Offshore Engine Engine Overspeeds
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil Filter Housing - Remove and Install
C175 Oil&Gas Offshore Engine Exhaust Temperature Is High
C175 Oil&Gas Offshore Engine Sensor Signal (Analog, Passive) - Test
An Installation Procedure for the TLV2 Seat Suspension Harness is Now Available {1408, 7324} An Installation Procedure for the TLV2 Seat Suspension Harness is Now Available {1408, 7324}
C7.1 Engines and Generator Sets Exhaust Has Excessive White Smoke
C7.1 Engines and Generator Sets Exhaust Has Excessive Black Smoke
C7.1 Engines and Generator Sets Engine Vibration Is Excessive
C7.1 Engines and Generator Sets Engine Top Speed Is Not Obtained
C175 Oil&Gas Offshore Engine Coolant Pressure Is Low
C7.1 Engines and Generator Sets Exhaust System Contains Fuel
C175-16 Locomotive Engines Engine Electronics
C7.1 Engines and Generator Sets Exhaust System Contains Oil
C175-16 Locomotive Engines Product Lifting
C175-16 Locomotive Engines Configuration Parameters
C175-16 Locomotive Engines Starting the Engine
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
C7.1 Engines and Generator Sets Fuel Contains Water
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
C7.1 Engines and Generator Sets Fuel Temperature Is High
Photovoltaic Inverters Electrical Connections and Termination - Single Phase Inverters
C7.1 Engines and Generator Sets Inlet Air Is Restricted