Solenoid Valve - Test - Engine
Use this procedure to troubleshoot a problem with a solenoid valve. Also, use this procedure if one of the following diagnostic codes is active or easily repeated.
Show/hide table
J1939 Code and Description | CDL Code and Description | Comments |
---|---|---|
4210-5
Engine Pre-lube Drive : Current Below Normal |
338-5
Engine Pre-Lube Pump Relay : Current Below Normal |
This code indicates that there is a problem with the prelubrication solenoid and/or the electrical circuit on the Electronic Control Module (ECM). |
4210-6
Engine Pre-lube Drive : Current Above Normal |
338-6
Engine Pre-Lube Pump Relay : Current Above Normal |
This code indicates that there is a problem with the prelubrication solenoid and/or the electrical circuit on the ECM. |
Electrical Checkouts on the Cat® Electronic Technician (ET)
Show/hide table
Component | Electrical Checkout |
---|---|
Engine Pre-lube Drive | Engine Pre-lube Override |
Show/hide table
Illustration 1 | g06105554 |
- Codes
- Open Circuit
- Short Circuit
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Check for Codes A. Connect Cat® Electronic Technician (ET) to the service tool connector. B. Determine if a code is active or logged. |
Codes |
Result: A -5 code is active or logged. Proceed to Test Step 2. Result: A -6 code is active or logged. Proceed to Test Step 3. |
2. Check the Wiring for an Open Circuit A. Verify that the harness connector is free of debris, free of corrosion and securely connected. B. Disconnect the solenoid from the harness. C. Connect a jumper wire between the terminals of the harness connector for the affected coil. The coil is replaced with a short circuit. |
Create a Short |
Result: A -5 code became active during the electrical checkout. The ECM did not detect the jumper wire. There is an open circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector. Repair: Repair or replace the connectors or the wiring. Verify that the repair eliminated the problem. Result: A -6 code is activated during the electrical checkout. The ECM detected the jumper wire. There is a problem with the solenoid. Repair: Replace the solenoid. Verify that the repair eliminated the problem. |
3. Check the Wiring for a Short Circuit A. Disconnect the solenoid from the harness. |
Create an Open |
Result: A -6 code became active during the electrical checkout. The ECM did not detect the open circuit. There is a short circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector. Repair: Repair or replace the connectors or the wiring. Verify that the repair eliminated the problem. Result: A -5 code is activated during the electrical checkout. The ECM detected the open circuit. There is a problem with the solenoid. Repair: Replace the solenoid. Verify that the repair eliminated the problem. |
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Caterpillar Information System:
C175 Tier 4 Final Engines for Off-Highway Trucks Solenoid Valve - Test - Aftertreatment
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Exhaust Has Excessive White Smoke
Fuel Line Serviceability for Certain Tier 4 C175 Engines {1100, 1101, 1252} Fuel Line Serviceability for Certain Tier 4 C175 Engines {1100, 1101, 1252}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Exhaust Temperature Is High
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Front Steering) - Remove and Install
Relay Compatibility Issue on Continuous Oil Prelube on 3508 Fire Pump Engines {1319} Relay Compatibility Issue on Continuous Oil Prelube on 3508 Fire Pump Engines {1319}
A New Turbine Inlet Bellows is Available for 3512 Locomotive Engines {1059} A New Turbine Inlet Bellows is Available for 3512 Locomotive Engines {1059}
C175-16 Oil and Gas Generator Set Model View Illustrations
G3512 Generator Set Engines Prelubrication Pump Problem
C4.4 and C6.6 Engines Valve Position - Test
Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000} Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}
C4.4 and C6.6 Engines Switch Circuits - Test - Air Filter Restriction Switch
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Remove and Install
C175 Tier 4 Final Engines for Off-Highway Trucks Diagnostic Trouble Codes
C175 Tier 4 Final Engines for Off-Highway Trucks Event Codes
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Conveyor Swing) - Remove and Install
C7.1 Marine Engine Water Temperature Regulator - Remove and Install
C175-16 Oil and Gas Generator Set Refill Capacities
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Conveyor Lift) - Remove and Install
C175-16 Oil and Gas Generator Set Maintenance Recommendations
C175-16 Oil and Gas Generator Set Marine Classification Society Certification Requirements
C7.1 Marine Engine Rocker Arm and Shaft - Remove
C7.1 Marine Engine Rocker Arm and Shaft - Install
G3512 Generator Set Maintenance Interval Schedule - Standby