New Basic Engine Components Are Used in C175-16 Engines {1202, 1205}
- Engine
- C175-16 (S/N: M6A1-UP)
Description Of Change: The following new components have been changed to increase the durability of the engine:
Crankshaft
Show/hide table
Illustration 1 | g02942880 |
Crankshaft |
- The diameter of the pin journal was reduced by 8 mm.
- The straight length of the pin journal was increased by 4 mm but the overall length of the crankshaft was not increased.
- The oil hole pattern was optimized to reduce cavitation.
- The dowels on the front and rear of the crankshaft were removed. For better serviceability, the dowels are now pressed into the rear crankshaft gear, the flywheel, and the damper.
Show/hide table
Illustration 2 | g02943082 |
Section view of the connecting rod |
- The connecting rod bore diameter was decreased by 7 mm (3.5 mm from each side). As a result, the thickness of the mating section for the connecting rod and the cap was increased. The thickness increases the rod stiffness and reduces bending under a load.
- A honed pattern was designed into the bearing bore instead of the previously shot-peened surface.
- The angle of the oil passage was changed from entering the bore at 15 degrees past top center to 40 degrees. The relocation of the oil passage moves the hole further from the loading zone.
- The oil hole for the rod eye bushing was relocated.
Show/hide table
Illustration 3 | g02943085 |
Bearing |
- The wall thickness was increased by 0.5 mm, which allows higher and more consistent contact pressure between the outer bearing diameter and the rod bore.
- The oil hole is now slotted and offset 40 degrees past the top center of the rod.
- Install the 376-6457 Connecting Rod Bearing in any of the new connecting rods for the odd-numbered cylinders.
- Install the 376-6458 Connecting Rod Bearing in any of the new connecting rods for the even-numbered cylinders.
Note: Do not mix the bearing halves between the different part numbers.
Crankshaft Vibration Damper
- The new damper is an oil fed damper which was needed to accommodate the dynamic changes of the crankshaft.
Adaptable To: The changes are effective with the following serial numbers:
- M6A00109
All the related parts are listed in Table 1
Show/hide table
Qty | New Part | Original Part |
1 | 146-3173 Dowel
(Damper) |
1S-2199 Dowel |
1 | 286-5311 Dowel
(Flywheel) |
|
1 | 345-8567 Dowel Pin
(Rear crankshaft gear) |
|
1 | 356-7064 Crankshaft | 317-8521 Crankshaft |
1 | 357-6282 Bushing | 229-9809 Bushing |
1 | 394-9595 Damper Gp | 317-1640 Damper Gp |
2 | 366-5649 Spacer | 269-0588 Spacer |
1 | 370-6546 Flywheel As | 334-8988 Flywheel As |
1 | 417-7902 Connecting Rod | 316-0062 Connecting Rod |
1 | 417-7903 Connecting Rod | 316-0063 Connecting Rod |
1 | 378-5615 Crankshaft Gear | 254-2075 Crankshaft Gear |
1 | 376-6457 Connecting Rod Bearing | 322-3031 Connecting Rod Bearing |
1 | 376-6458 Connecting Rod Bearing | 322-3030 Connecting Rod Bearing |
1 | 421-3978 Stub Shaft As | 361-8834 Stub Shaft |
12 | 388-1521 Bolt | 276-8999 Bolt |
Caterpillar Information System:
A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Machine Engines {1207} A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Machine Engines {1207}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620} New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
Identifying Oil Pumps on Certain C27, C32, and 3412 Engines {1304} Identifying Oil Pumps on Certain C27, C32, and 3412 Engines {1304}
HPU300 Hydraulic Power Pack Daily Inspection
HPU300 Hydraulic Power Pack Storage
C12.9 Marine Engines Camshaft Bearings - Remove and Install
SPF343 and SPF343C Trailer Mounted Pumpers Monitoring System
PM820, PM822, and PM825 Cold Planer Machine Systems Flashing (Conveyor) - Remove and Install
SPF343 and SPF343C Trailer Mounted Pumpers Gauges and Indicators
SPF343 and SPF343C Trailer Mounted Pumpers Coolant Level - Check
SPF343 and SPF343C Trailer Mounted Pumpers Manual Stop Procedure
SPF343 and SPF343C Trailer Mounted Pumpers Engine Oil Level - Check
C12.9 Marine Engines Crankshaft Front Seal - Remove and Install
M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000} M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000}
C175 Tier 4 Final Engines for Off-Highway Trucks DEF Pressure Does Not Respond
C175-16 and C175-20 Locomotive Engines Valve Lifter - Install
Front Suspension Failures May Occur on Certain 777D/777F/777G Off-Highway Trucks {7200, 7201, 7551} Front Suspension Failures May Occur on Certain 777D/777F/777G Off-Highway Trucks {7200, 7201, 7551}
C175-16 and C175-20 Locomotive Engines Air Inlet Manifold - Remove and Install
C175-16 and C175-20 Locomotive Engines Fuel Pump (High Pressure) - Remove and Install
349F and 352F Excavators Machine System Specifications Swing Drive - Left Swing Drive and Right Swing Drive
ECPC Valves May Fail on Cat Transmission Systems {3073, 3139, 3167} ECPC Valves May Fail on Cat Transmission Systems {3073, 3139, 3167}
C4.4 and C6.6 Engines Diagnostic Trouble Codes
HPU300 Hydraulic Power Pack Hydraulic Oil Filter - Replace
A New Cylinder Liner Assembly And Piston Is Now Used For Certain 3516 Locomotive Engines {1201, 1216} A New Cylinder Liner Assembly And Piston Is Now Used For Certain 3516 Locomotive Engines {1201, 1216}