New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920}
- Generator Set
- G3512E (S/N: SSR1-UP; NGS1-UP)
- G3520E (S/N: GZE1-UP; GZG1-UP; GZH1-UP)
Description Of Change: The new engine software has updates on the engines that are listed above and contains the following improvements:
- 0% secondary voltage diagnostic code.
- Tecjet diagnostic update for engines that uses a Tecjet.
- Hard Start Repair (Close fuel valve when the GSOV is closed).
- GSOV Failure Diagnostics.
- Even bank detonation shutdown repair for 20 cylinder engines.
Adaptable To: The new software is a direct replacement for the former software. Refer to Table 1 for the new and former engine software part numbers. The new software is adaptable back to the first production on the serial numbers listed above.
Show/hide table
| New Software Part Number | Former Software Part Number |
| 495-4116 Engine Ratings Electronic Software Gp | 361-2907 Engine Ratings Electronic Software Gp |
| 495-4120 Engine Ratings Electronic Software Gp | 288-4375 Engine Ratings Electronic Software Gp |
| 495-4123 Engine Ratings Electronic Software Gp | 288-4376 Engine Ratings Electronic Software Gp |
| 495-4124 Engine Ratings Electronic Software Gp | 333-5459 Engine Ratings Electronic Software Gp |
| 495-4125 Engine Ratings Electronic Software Gp | 450-2450 Engine Ratings Electronic Software Gp |
| 495-4126 Engine Ratings Electronic Software Gp | 361-4285 Engine Ratings Electronic Software Gp |
Show/hide table
| Effective Serial Numbers |
| G3512E |
| S/N:NGS00168-UP |
| S/N:SSR00250-UP |
| G3520E |
| S/N:GZE00405-UP |
| S/N:GZG00002-UP |
| S/N:GZH00168-UP |
Caterpillar Information System:
G3516 TA Engine Engine Governing
G3516 TA Engine Electronic Control System Operation
New Scraper Mounting for Certain Asphalt Compactors {6607} New Scraper Mounting for Certain Asphalt Compactors {6607}
C12.9 Marine Engines Sensors and Electrical Components
C18 Generator Set Engines Fuel Priming Pump - Remove and Install
C12.9 Marine Engines Starting Aid (Air Inlet Heater) - Inspect/Clean/Replace
A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258} A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258}
New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137} New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137}
New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059} New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059}
Cat® Command For Hauling E1189
C11 and C13 Engines for Caterpillar Built Machines Gear Group (Rear) - Remove and Install
C11 and C13 Petroleum Engines Gear Group (Rear) - Remove and Install
New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900} New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900}
Check for the Correct Bolt Torque for the Air Shutoff Butterfly Plate on Certain 3500 Engines {1078} Check for the Correct Bolt Torque for the Air Shutoff Butterfly Plate on Certain 3500 Engines {1078}
795F AC and 795F AC XQ Off-Highway Trucks Hood Tilt
Caterpillar Machine Fluids Recommendations Warranty Information
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000} Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
G3516 TA Engine Engine Sensors
G3508J, G3516J, and G3520J Engines Fuel Control Valve - Remove and Install
G3516 TA Engine Ignition System
Caterpillar Machine Fluids Recommendations Reference Material
G3516 TA Engine Gas Pressure Regulator