Sensors and Electrical Components
Če želite več informacij o tipalih in konektorjih, glejte priročnik Odpravljanje težav , M0064896.
Show/hide table
| |
| Slika 1 | g06010068 |
|
(1) Tipalo temperature izpušnih plinov (če je stroj tako opremljen)
(2) Tipalo temperature in tlaka vhodnega zraka (3) Tipalo tlaka in temperature spodnjega nizkotlačnega hladilnika polnilnega zraka (4) Stikalo nizkega nivoja hladilne tekočine (če je stroj tako opremljen) (5) Tipalo temperature zraka v polnilnem zbiralniku (IMAT) (6) Tipalo tlaka zraka v polnilnem zbiralniku (IMAP) (7) Stikalo za zamašen filter za gorivo (8) Tipalo temperature goriva | |
Show/hide table
| |
| Slika 2 | g06010084 |
|
(1) Krmilni ventil visokotlačne črpalke za gorivo
(2) Tipalo tlaka nizkotlačnega sistema za gorivo (3) Tipalo tlaka morske vode (4) Tipalo hitrosti vrtenja odmične gredi (5) Tipalo temperature in tlaka dovoda zraka (6) Stikalo za zamašen oljni filter (7) Tipalo tlaka okrova ročične gredi | |
Show/hide table
| |
| Slika 3 | g06010125 |
|
(1) Tipalo temperature izpušnih plinov (če je stroj tako opremljen)
(2) Tipalo hitrosti vrtenja ročične gredi (3) Tipalo hitrosti vrtenja turbinskega polnilnika (samo različica s 1000 KM) | |
Show/hide table
| |
| Slika 4 | g06010150 |
|
(1) Tipalo temperature in tlaka olja
(2) Tipalo temperature hladilne tekočine (3) Tipalo tlaka in temperature spodnjega nizkotlačnega hladilnika polnilnega zraka | |
Show/hide table
| |
| Slika 5 | g06010252 |
| (1) Tipalo tlaka voda za gorivo | |
Okvaro kateregakoli tipala lahko povzroči ena od naslednjih motenj:
- izhod tipala je odprt,
- kratek stik med izhodom tipala in "negativnim" ali "pozitivnim" priključkom akumulatorja,
- izmerjeni odčitek tipala ne ustreza specifikacijam.
Caterpillar Information System:
C18 Generator Set Engines Fuel Priming Pump - Remove and Install
C12.9 Marine Engines Starting Aid (Air Inlet Heater) - Inspect/Clean/Replace
A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258} A New Caterpillar Regeneration System (CRS) Pump Is Now Used For Certain Tier 4 Final Engines {1258}
New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137} New O-Ring Seal Kit Is Available for Use on Raptor Fuel Valve Sensor Module {1741, 5137}
New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059} New 441-4414 Exhaust Manifold Is Available for Use on Certain G3520C Landfill Engines {1059}
Cat® Command For Hauling E1189
C11 and C13 Engines for Caterpillar Built Machines Gear Group (Rear) - Remove and Install
C11 and C13 Petroleum Engines Gear Group (Rear) - Remove and Install
C1.7 and C2.2 Industrial Engine Relay - Test - Start Relay
C12.9 Marine Engines Engine Speed/Timing Sensor - Clean/Inspect
Installing Inducement Override Switch and Wiring for 3516C & C175-16 Tier 4I Engines That Uses an EMCP 4.2 Panel {1408, 7405, 7451, 7553, 7556} Installing Inducement Override Switch and Wiring for 3516C & C175-16 Tier 4I Engines That Uses an EMCP 4.2 Panel {1408, 7405, 7451, 7553, 7556}
New Crankshaft Seals Are Now Used on Certain 3524 Engines {1000, 7555} New Crankshaft Seals Are Now Used on Certain 3524 Engines {1000, 7555}
New Scraper Mounting for Certain Asphalt Compactors {6607} New Scraper Mounting for Certain Asphalt Compactors {6607}
G3516 TA Engine Electronic Control System Operation
G3516 TA Engine Engine Governing
New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920} New Engine Diagnostic Codes Software is Now Used on G3500E Gas Engines {1920}
New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900} New Control Harness Assemblies Are Now Used on Certain G3306B Engines {1408, 1900}
Check for the Correct Bolt Torque for the Air Shutoff Butterfly Plate on Certain 3500 Engines {1078} Check for the Correct Bolt Torque for the Air Shutoff Butterfly Plate on Certain 3500 Engines {1078}
795F AC and 795F AC XQ Off-Highway Trucks Hood Tilt
Caterpillar Machine Fluids Recommendations Warranty Information
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000} Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000} A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
G3516 TA Engine Engine Sensors