3500 Generator Sets with Dynamic Gas Blending Caterpillar


Maintenance Interval Schedule - Standby

Usage:

3512B 4AW
在进行任何操作或维护步骤之前,确保已阅读并理解所有的安全信息、警告和说明。 用户负责执行维护,包括所有的调整,使用适当的润滑剂、油液和滤清器。 用户还负责由于正常磨损和老化而更换部件。 未能遵照正确的保养周期和步骤可能导致产品性能降低和/或部件磨损加速。 使用燃油消耗量、工作小时数或日历时间(以先到者为准)确定保养周期。 在恶劣作业条件下工作的产品可能需要更频密的保养。 在进行每个后续周期的保养之前,必须先进行前一个周期的所有保养。

需要时即进行的保养

蓄电池 - 回收
蓄电池 - 更换
蓄电池或蓄电池电缆 - 断开
断路器 - 复位
燃油系统 - 充油
燃油系统粗滤器/油水分离器 - 放水
发电机 - 干燥处理
发电机轴承 - 润滑
发电机组 - 测试
发电机组绕组 - 测试

每天的保养

功率因数 - 检查

每周

进气滤清器 - 检查/清洁/测试
空气起动马达润滑器油位 - 检查
储气罐水份和沉积物-排放
蓄电池充电器 - 检查
蓄电池电解液液位 - 检查
控制面板 - 检查/测试
冷却液液位 - 检查
电气连接 - 检查
发动机空气滤清器保养指示器 - 检查
发动机空气预滤器 - 检查/清洁
发动机机油油位 - 检查
燃油箱中的水和沉渣 - 排放
发电机 - 检查
发电机轴承 - 检查
发电机轴承温度 - 测试/记录
发电机导线 — 检查
发电机负载 - 检查
水套水加热器 - 检查
功率因数 - 检查
空间加热器 - 测试
备用发电机组保养建议
定子绕组温度 - 测试
电压和频率 - 检查
绕机检查

每250个工作小时的保养

空气切断 - 测试

每 6 个月

冷却液液样(1 级)- 采样

每500个工作小时或1年

风扇传动轴承 - 润滑

每年的保养

空气起动马达润滑器油杯 - 清洗
交流发电机-检查
皮带 - 检查/调节/更换
冷却液液样(2 级)- 采样
冷却系统补充用冷却液添加剂(SCA)- 测试/添加
曲轴箱压力 - 测量
曲轴减振器 - 检查
发动机 - 清洁
发动机空气滤清器滤芯(双滤芯)- 检查/清洁/更换
发动机空气滤清器滤芯(单滤芯)- 检查/清洁/更换
发动机曲轴箱呼吸器 - 清洗/更换
发动机安装基座 - 检查
发动机机油油样 - 采样
发动机机油和滤清器 - 更换
发动机保护装置 - 检查
发动机转速/正时传感器 - 清洁/检查
发动机阀间隙 - 检查
喷油器 - 检查/调整
燃油系统粗滤器(油水分离器)滤芯 - 更换
燃油系统细滤器 - 更换
燃气滤清器冷凝水 - 排放
燃气压力调节器冷凝水 - 排放
发电机组振动 - 测试/记录
发电机绕组绝缘 - 测试
软管和卡箍 - 检查/更换
氧传感器 - 标定
预润滑泵 - 检查
散热器 - 清洁
旋转整流器 - 检查/测试
起动马达 - 检查
定子引线 - 检查
变阻器 - 检查
变阻器 - 检查
水泵 - 检查

每2000工作小时

喷油器 - 检查/调整

每3年

冷却液 (DEAC) - 更换
冷却液温度调节器 - 更换
涡轮增压器 - 检查

每6年

冷却液 (ELC) - 更换
冷却液长效剂(ELC)- 添加

试运转

风扇传动轴承 - 润滑
发电机组对中 - 检查

Caterpillar Information System:

3500 Generator Sets with Dynamic Gas Blending Maintenance Interval Schedule - Prime
C8.7 Marine Engine Exhaust Manifold - Remove and Install
C7.1 Commercial Marine Engine Coolant Contains Oil
C7.1 Commercial Marine Engine Battery Problem
C7.1 Commercial Marine Engine Alternator Problem
C18 Generator Set Maintenance Interval Schedule
C7.1 Commercial Marine Engine Alternator Is Noisy
C18 Generator Set Maintenance Interval Schedule - Standby
C18 Generator Set Maintenance Interval Schedule - Prime Power
C7.1 Commercial Marine Engine Acceleration Is Poor or Throttle Response Is Poor
2015/07/31 New Software Is Used on Certain 3516C Commercial Engines {1920}
C7.1 Commercial Marine Engine System Configuration Parameters
G3606 and G3608 Engines Engine Oil Filler - Remove and Install
Zip-Tie Installation Guide{0374, 0599, 7000} Zip-Tie Installation Guide{0374, 0599, 7000}
UPS 250 and UPS 300 Uninterruptible Power Supplies Safety Signs and Labels
UPS 250 and UPS 300 Uninterruptible Power Supplies General Hazard Information
UPS 250 and UPS 300 Uninterruptible Power Supplies Fire Prevention and Explosion Prevention
UPS 250 and UPS 300 Uninterruptible Power Supplies Electrical System
UPS 250 and UPS 300 Uninterruptible Power Supplies Model View Illustrations
UPS 250 and UPS 300 Uninterruptible Power Supplies System Description
UPS 250 and UPS 300 Uninterruptible Power Supplies Specifications
UPS 250 and UPS 300 Uninterruptible Power Supplies Generator Set Start Module
UPS 250 and UPS 300 Uninterruptible Power Supplies UPS View Software
UPS 250 and UPS 300 Uninterruptible Power Supplies Modem
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.