740 GC, 740 Ejector, 745 Articulated Truck Power Train Caterpillar


Output Transfer Gears - Remove and Install

Usage:

745 3F6


拆卸步骤

开始:

  1. 安装转向机架锁。

  2. 拆下散热器组件。

  3. 拆下主驱动轴。

  4. 拆卸前驱动轴。


注意

在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。

有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。

按照当地法规和要求处置所有液体。


  1. 将分动器油排入适当的容器。 有关正确的步骤,请参阅操作和保养手册,“分动器 - 机油更换”。

  2. 断开铰接传动轴。 有关正确的步骤,请参阅“铰接传动轴 - 拆卸和安装”。


    图 1g03841836

  3. 如果配备有后排气总成 (1),使用适当的支座夹住排气总成 (1) 并拆下管 (2)。


    图 2g03859461

  4. 断开软管组件 (3) 和 (5)。 断开线束组件 (4)。


    图 3g03859478


    图 4g03859719

    注: 为便于拍照,转向机架锁已拆下。

  5. 将适当的起吊设备连接到分动器 (6) 上。 分动器 (6) 的重量约为 204 kg (450 lb)

  6. 拆下螺栓 (7) 和垫圈。 对另一侧重复此操作。

  7. 拆下螺栓 (8) 和垫圈。 松开螺栓 (9)。 对另一侧重复此操作。


    图 5g03859729

  8. 拆下分动器 (6)。 如有必要,拆下顶部安装组件。

安装步骤

  1. 按与拆卸相反的顺序安装分动器 (6)。

Caterpillar Information System:

422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Final Drive Planetary - Remove and Install - Front
AP255E Asphalt Paver Engine Supplement Exhaust (Muffler) - Remove and Install
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Steering Cylinder (Front) - Remove and Install
AP255E Asphalt Paver Engine Supplement Gear Pump (Fan Drive) - Remove
AP300F Asphalt Paver Engine Starting
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Tie Rod (Steering)(Front) - Remove and Install
AP300F Asphalt Paver Hopper Travel Lock
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Refrigerant Compressor - Remove and Install
SE34 V and SE34 VT Asphalt Screeds Screed Service Locks
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Check Valve
AP355F Asphalt Paver Decelerator Control
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Alternator - Remove and Install
3412E Engine for 773E Off-Highway Trucks Sensor Signal (Analog, Active) - Test
2015/06/02 Expansion Of Reman Hydraulic Pumps {5070, 7754}
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Final Drive Planetary - Remove and Install - Rear
AP355F Asphalt Paver Push Roller
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Electrical Power Supply - Test
PL83 and PL87 Pipelayers Engine Supplement Catalyst (SCR) - Remove and Install
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train Electronic Control System MID 027 - CID 1893 - FMI 12
AP355F Asphalt Paver Machine Cleanup Procedure
Bolt Inspection on 450F Backhoe Loader For Leaking Seal Kit On Hydraulic Gear Pump{5073} Bolt Inspection on 450F Backhoe Loader For Leaking Seal Kit On Hydraulic Gear Pump{5073}
AP355F Asphalt Paver Shipping the Machine
PL83 and PL87 Pipelayer Systems Pivot Shaft
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Drive Shaft (Front) - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.