Electric Starting Motor - Remove and Install
Removal Procedure
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Open the left access door.
- Turn the battery disconnect switch to the OFF position.
- Remove the four bolts, the four washers, and cover (1). Cover (1) is located under the machine directly below the electric starting motor.
Show/hide table
Illustration 1 | g03062957 |
- Remove the nut, the washer, cable assembly (3), and cable assembly (4) .
Show/hide table
Illustration 2 | g03726057 |
- Remove the nut, the washer, grounding strap (5), and cable assembly (6) .
- Remove the nut, the washer, and harness assembly (7) .
- Remove three bolts (8), the three washers, and electric starting motor (2) .
Installation Procedure
- Install electric starting motor (2) in the reverse order of removal.
- Tighten the nut securing grounding strap (5) and cable assembly (6) to a torque of 21 ± 3 N·m (186 ± 27 lb in).
- Tighten the nut securing cable assembly (3) and cable assembly (4) to a torque of 16 ± 3 N·m (141 ± 27 lb in).
Caterpillar Information System:
CW34 Pneumatic Compactor Engine Supplement Battery - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Alternator Belt - Remove and Install
C7.1 Industrial Engine DEF Filler Screen - Clean
CW34 Pneumatic Compactor Engine Supplement Air Cleaner - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Selector and Pressure Control Valve (Secondary Steering)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Engine and Transmission Mounting
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control Valve
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Air Cleaner
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Air Cleaner - Mounting
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Steering)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Air Conditioner Lines
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Torque Converter Cooler Lines
CW34 Pneumatic Compactor Engine Supplement Engine - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Engine Enclosure (Hood) - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Expansion Tank - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Gear Motor (Hydraulic Fan) - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Manifold Valve (Bypass) - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Muffler - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Primary Fuel Filter, Water Separator and Base - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Refrigerant Compressor - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control Support
735C and 745C Articulated Trucks Torque Converter, Transmission, and Transfer Gear Oil Filter - Replace