Fuel Pressure Sensor - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 370-8376 | 封盖套件 | 1 |
Show/hide table
接触高压燃油可能导致液体渗透和烧伤危险。 高压燃油溢出可能会产生火灾。 如果不遵循检查、保养和维修指南,可能会造成人身伤亡。 |
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
- 拆下燃油压力传感器时,必须安装新燃油压力传感器。
Show/hide table
图 1 g03411830 - 拆下六角头螺栓 (5),然后拆下支架 (1)。 将支架远离燃油压力传感器 (3)。
- 将线束组件 (4) 从燃油压力传感器 (3) 上断开。
- 用深孔套筒将燃油压力传感器 (3) 从燃油歧管 (2) 上拆下。
- 用工具 (A) 盖住燃油压力传感器 (3)。 用工具 (A) 塞住燃油歧管 (2)。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | - | Bosch 润滑脂 Ft1v27 | 1 |
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保新燃油压力传感器 (3) 和燃油歧管 (2) 无磨损或损坏。 更换任何损坏或磨损的部件。
- 将螺塞从燃油歧管 (2) 上拆下。
- 立即清洁燃油歧管 (2) 中用于燃油压力传感器 (3) 的螺纹。 确保螺纹清洁、无碎屑。 确保燃油歧管 (2) 中的螺纹无损坏。
- 清洁和检查后,立即用工具 (A) 盖住燃油歧管 (2) 的打开端口。
- 将盖从燃油压力传感器 (3) 的螺纹端拆下。 用工具 (B) 稍稍润滑安全阀的螺纹和钻刃 (6)。
- 将螺塞从燃油歧管 (2) 上拆下。
- 用深孔套筒将燃油压力传感器 (3) 安装到燃油歧管 (2) 上。 拧紧燃油压力传感器至扭矩为
70 N·m (52 lb ft) 。 - 将线束组件 (4) 连接到燃油压力传感器 (3) 上。
- 将支架 (1) 定位在废气旁通阀电磁阀上。
- 将六角头螺栓 (5) 安装到支架 (1) 上。 拧紧六角头螺栓至扭矩为
5 N·m (44 lb in) 。 - 排出燃油系统中的空气。 参考操作和保养手册, "燃油系统 - 充注"以了解正确步骤。
Show/hide table
图 2 | g03411830 |
Show/hide table
图 3 | g03444696 |
Caterpillar Information System:
C13 Generator Set Engine Fan Drive - Assemble
C13 Generator Set Engine Fan Drive - Disassemble
C9.3 Industrial Engine Product Lifting
EMCPll+ Software Not Compatible With Certain G3400 Engines{4490} EMCPll+ Software Not Compatible With Certain G3400 Engines{4490}
C9.3 Industrial Engine Plate Locations and Film Locations
C13 Generator Set Engine Fan Drive - Remove and Install
3516C Locomotive Engines Selective Catalytic Reduction Component Location
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Engine Overspeeds
C3.4B Industrial Engine After Starting Engine
C13 Generator Set Engine Fan Guard - Remove and Install
C13, C15, and C18 Generator Set Engines Turbocharger Oil Lines
C13, C15, and C18 Tier 4 Final Engines Cover Group (Front Housing)
371-0351 Hydraulic Valve Seat Puller Group {0374, 0599, 0700, 0703} 371-0351 Hydraulic Valve Seat Puller Group {0374, 0599, 0700, 0703}
C27 and C32 Generator Sets Product Description
2015/08/19 An Improved Seat Belt Group is Now Available for 311 through 390 Excavators {7327}
2013/07/30 New Service Replacement Stator Part Numbers for Certain XQ60, XQ100, and XQ175 Generator Sets are Now Available {4453}
3516C Marine Engines Water Lines
C3.4B Industrial Engine Fuel Related Components in Cold Weather
C13 Generator Set Engine Fan - Remove and Install
3516C Marine Engines Engine Oil Lines
UPS 750 Uninterruptible Power Supply DC Bus Capacitor - Replace
2013/08/30 New Software and Low Pressure Fuel System Are Used in Certain C175 Engines {1250, 1901, 1902}
2013/11/25 New Breather Assemblies Are Now Used on Certain C175 Engines {1317}
3516C Petroleum Engines Flywheel Housing