C15 and C18 Industrial Engines Caterpillar


Fuel Filter Base - Remove and Install

Usage:

C15 N5F

拆卸步骤

表 1
所需工具 
工具  零件号  零件描述  数量 
185-3630  带式扳手组件 
LOCTITE 271 

  1. 将燃油供应转到 OFF 位置,并将电源断路开关转到 OFF 位置。


    图 1g03397615

  2. 断开线束组件 (2) 并拆下传感器 (7)。 拆下螺母 (1),然后将支架 (6) 放置到一边。 断开软管组件 (4) 和管组件 (5)。 使用工具 (A) 拆下燃油滤清器 (9)。 拆下螺栓 (3),然后拆下燃油滤清器底座 (8)。

  3. 拆下燃油滤清器底座 (5)。


    图 2g03397629

  4. 拆下适配器组件 (10) 和螺柱 (11)。

安装步骤

  1. 按与拆卸相反的顺序安装燃油滤清器底座 (8)。


      图 3g03397632

    1. 将工具 (B) 涂抹到螺柱 (11) 的螺纹上。 工具 (B) 应覆盖住双头螺栓的螺纹,如尺寸 (C) 所示,其为 7.6 ± 0.8 mm (0.3 ± 0.03 inch) 的测量值。

    2. 将螺柱 (11) 拧紧至扭矩为 70 ± 15 N·m (52 ± 11 lb ft)

    3. 将燃油温度传感器拧紧至扭矩 20 ± 3 N·m (177 ± 27 lb in)

    4. 拧紧燃油压力传感器至扭矩为 10 ± 2 N·m (89 ± 18 lb in)

    5. 在安装之前,用油液润滑即将密封的燃油滤清器密封件。 使用工具 (A) 拧紧燃油滤清器 (9) 至扭矩为 35 ± 3 N·m (26 ± 2 lb ft)

Caterpillar Information System:

3512E Tier 4 Final Engines for Land Electric Drilling Sensor Calibration Required - Test
2013/09/25 New All Metal Fuel and Water Separators Are Used For Certain Machines {1261, 1263}
3516E Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000} 142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}
2013/07/01 New Jacket Water Heating Element Used in Certain C9 Generator Set Engines {1383}
SPF343 and SPF343C Trailer Mounted Pumpers Fluid Recommendations
C13 Generator Set Refill Capacities
3512C Oil Well Service Engines Monitoring System
3512C Oil Well Service Engines Product Description
349F and 352F Excavators Hydraulic System Solenoid Valve (Proportional Reducing) - Calibrate - Boom Down Regeneration
C13 Generator Set Product Description
Well Service Pumps Product Storage
C15 and C18 Industrial Engines Fuel Transfer Pump - Remove and Install
C15 and C18 Industrial Engines Exhaust Cooler (NRS) - Remove and Install
2014/07/18 A New Auxiliary Water Pump Group is Used in Certain CG137 and G3400 Engines {1371}
C15 and C18 Industrial Engines Air Control Valve - Remove and Install
Troubleshooting Procedure for the Failure of All Refueling Pumps {1295} Troubleshooting Procedure for the Failure of All Refueling Pumps {1295}
WS273 XD, WS305 XD, WSF273 XD, WSF305 XD, WSP273 and WSP305 Well Stimulation Pumps Crosshead - Assemble
WS273 XD, WS305 XD, WSF273 XD, WSF305 XD, WSP273 and WSP305 Well Stimulation Pumps Crosshead - Disassemble
C175-16 Locomotive Engine Engine Coolant Temperature Sensor
325D and 329D Excavators Hydraulic System Accumulator (Pilot) - Test and Charge
G3500B Engines Engine Shutdown Occurs Intermittently
3516C Petroleum Engines Engine Oil Filter Housing - Disassemble
3500B Locomotive Engines Belts - Inspect/Adjust/Replace
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.