Power Take-Off Drive Group - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 (5/8 - 18 x 8 in) |
2 |
B | 1P-0520 | 冲头总成 | 2 |
C | 9S-3263 | 螺纹锁固胶 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用工具 (B) 将套筒轴承 (13) 装入飞轮壳中。 套筒轴承中槽口的位置应保持角度 (Y),即距水平中心线 15 ± 1 度。 轴承应当安装到深度 (Z),即
2.0 ± 0.5 mm (0.08 ± 0.02 in) 。 - 利用工具 (B) 将套筒轴承 (12) 装入飞轮壳中。 套筒轴承中槽口的位置应保持角度 (X),即距竖直中心线 15 ± 1 度。 轴承应当安装到深度 (Z),即
2.0 ± 0.5 mm (0.08 ± 0.02 in) 。 - 将 O 形密封圈安装在盖 (11) 上。 将盖 (11) 和螺栓安装在飞轮壳体的背面。
Show/hide table
图 2 g01106649 - 将齿轮组件 (9) 和齿轮组件 (10) 安置在飞轮壳体中。
Show/hide table
图 3 g01106948 - 利用工具 (B) 将套筒轴承 (3) 装入转接接头 (2) 中。 在接头 (2) 上安装O形密封圈。
Show/hide table
图 4 g01106976 - 将套筒轴承内的溢油槽与惰齿轮 (6) 内的溢油槽对齐。 利用工具 (B) 将套筒轴承装入惰齿轮 (6) 中。
- 定位惰齿轮 (6) 和护圈 (5)。 安装螺栓 (4)。
- 将套筒轴承内的溢油槽与惰齿轮 (7) 内的溢油槽对齐。 利用工具 (B) 将套筒轴承装入惰齿轮 (7) 中。
- 定位惰齿轮 (7) 和护圈 (5)。 安装螺栓 (4)。
- 将 O 形密封圈装入曲轴齿轮 (8) 的沉孔中。 用清洁的发动机机油润滑 O 形密封圈。 将曲轴齿轮 (8) 安装到工具 (A) 上。
- 将转接接头 (2) 定位到飞轮壳上。 将工具 (C) 涂抹在螺栓 (1) 的螺纹上后安装螺栓。
Show/hide table
图 1 | g01106888 |
结束:
- 安装飞轮。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Disassemble
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 Marine Generator Set Engine Operation
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C13 and C15 Generator Sets After Starting Engine
C18 Generator Set Model View Illustrations