Power Take-Off Drive Group - Disassemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 (5/8 - 18 x 8 in) |
2 |
B | 1P-0520 | 冲头总成 | 2 |
开始:
- 拆下飞轮。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (1 )。 将转接接头 (2) 从飞轮壳上拆下。
- 从转接接头 (2) 上拆下 O 形密封圈。 利用工具 (B) 将套筒轴承 (3) 从转接接头 (2) 上拆下。
- 卸下螺栓 (4)。 拆下护圈组件 (5) 和惰齿轮 (6)。 利用工具 (B) 将套筒轴承从惰齿轮 (6) 上拆下。
- 卸下螺栓 (4)。 拆下护圈组件 (5) 和惰齿轮 (7)。 利用工具 (B) 将套筒轴承从惰齿轮 (7) 上拆下。
- 将曲轴齿轮 (8) 从工具 (A) 上拆下。 将 O 形密封圈从曲轴齿轮的沉孔中拆下。
Show/hide table
图 2 g01106649 - 从飞轮壳体上卸下齿轮组件 (9) 和齿轮组件 (10)。
Show/hide table
图 3 g01106650 - 将螺栓和盖 (11) 从飞轮壳的背面上拆下。 将 O 形密封圈从盖上拆下。 利用工具 (A) 将套筒轴承 (12) 从飞轮壳上拆下。
- 将螺栓和盖 (11) 从飞轮壳的背面上拆下。 将 O 形密封圈从盖上拆下。 利用工具 (A) 将套筒轴承 (13) 从飞轮壳上拆下。
Show/hide table
图 1 | g01106648 |
Caterpillar Information System:
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 Marine Generator Set Engine Operation
C18 Generator Set Safety Messages
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Assemble
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C13 and C15 Generator Sets After Starting Engine