Water Pump - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
D | 1P-0510 | 冲头总成 | 1 |
E | 138-9299(1) | 密封工具 | 1 |
E | FT-3171(2) | 密封工具 | 1 |
F | 139-0088(1) | 密封工具 | 1 |
F | 325-5756(2) | 密封工具 | 1 |
Show/hide table
(1) | 用于 |
(2) | 用于 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁水泵轴 (6) 和壳体 (1) 中唇形密封 (9) 的沉孔。
- 使用工具 (D) ,将新的唇形密封 (9) 安装到壳体 (1) 中。
注: 安装密封时使密封金属表面上的零件号朝向壳体。 确保唇形密封与壳体沉孔的前边缘平齐。 请勿润滑唇形密封。 使用压具安装唇形密封。 请勿用手安装唇形密封。
- 将轴承组件 (8) 安装在水泵轴 (6) 上。
- 安放护圈 (5),使 “OUTSIDE”(外侧)标记朝向水泵轴 (6) 的齿轮端。
- 利用压具将齿轮 (2) 安装到水泵轴 (6) 上。
注: 安装齿轮 (2),使其紧贴轴承组件 (8)。
- 将工具 (E) 在轴 (6) 的上方滑动。 锥边缘将朝向外侧。
- 将齿轮 (2) 和水泵轴安装到壳体 (1) 中。 小心不要损坏唇形密封 (9)。 安装将轴承挡圈 (5) 固定在壳体上的螺栓 (3) 。
- 将工具 (E) 从水泵轴 (6) 上拆下。
- 利用压具和工具 (F) 将新密封总成 (7) 安装到轴 (6) 上和壳体 (1) 中。 确保密封外侧壳体完全座入壳体中。
- 将叶轮 (4) 在水泵轴 (6) 上放置到位。 利用压具将叶轮 (4) 安装到水泵轴上。
注: 安装叶轮 (4) 时应距水泵轴端
0.00 ± 0.25 mm (0.000 ± 0.010 in) 以内。 - 将 O 形密封圈 (10) 安装在壳体上。
Show/hide table
图 1 | g01021798 |
结束:
- 安装水泵。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 Marine Generator Set Engine Operation
C18 Generator Set Safety Messages
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C7.1 Industrial Engine Electrical System
C7.1 Marine Generator Set Starting with Jump Start Cables
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Assemble
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release