C15 and C18 Engines for Caterpillar Built Machines Caterpillar


Engine Oil Pump - Assemble

Usage:

826K 232

组装步骤

表 1
所需工具 
工具  零件号  零件描述  数量 
1P-0510  冲头总成 


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。




图 1g01053962

  1. 利用工具 (B) 将套筒轴承 (11) 装入泵体中。 轴承接头应距两个轴承孔中心线 30 ± 15 度。 安装套筒轴承,使套筒轴承与泵体的外侧齐平。

  2. 最终组装前,检查机油泵所有零件的状态和技术规格。 请参阅技术规格, "机油泵"。


    图 2g01043546

    ------ WARNING! ------

    弹簧压缩零件如果安装不当,会伤害人体。

    为避免伤害,遵照出版的装配程序,并穿上保护装备。


  3. 使用清洁的发动机机油润滑惰齿轮和驱动齿轮。 使用清洁的发动机机油润滑套筒轴承 (11)。 将惰齿轮 (5) 和驱动齿轮 (4) 安装到泵体 (3) 中。

  4. 安装盖 (10)。 通过安装螺栓 (12) 将盖固定到泵体上。

    注: 在组装后发动机机油泵必须能转动自如。 用手转动发动机机油泵。 如果发动机机油泵不能转动自如,重新安置盖 (10)。

  5. 安装安全阀柱塞 (7)、弹簧 (8)、护圈 (9) 和螺栓 (6)。

  6. 将键安装在轴上。


    图 3g01043619

  7. 将驱动齿轮 (1) 安装到机油泵 (2) 的轴上。 安装螺栓 (13)。 拧紧螺栓至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)

结束:

  1. 安装发动机机油泵。

Caterpillar Information System:

C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 Marine Generator Set Engine Operation
C18 Generator Set Safety Messages
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C7.1 Industrial Engine Electrical System
C7.1 Marine Generator Set Starting with Jump Start Cables
C7.1 Marine Generator Set Starting the Engine
C13 and C15 Generator Sets Plate Locations and Film Locations
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Assemble
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.