Engine Oil Filter Housing - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 在壳体 (11) 内安装旁通阀 (14) 和弹簧 (13)。
注: 旁通阀在孔中应自由移动。
- 将 O 形密封圈安装在盖 (5) 上。 安装盖 (5) 和螺栓 (4)。
- 将 O 形密封圈安装在盖 (10) 上。 安装盖 (10) 和螺栓 (9)。
- 如有必要,将定位销安装在壳体 (11)中。 定位销必须在壳体面以上
6.50 ± 1.00 mm (0.256 ± 0.040 in) 。 - 在壳体 (11) 上安装 O 形密封圈。 将壳体支架 (6) 安装到壳体 (11)上。 安装螺栓 (12),并拧紧至扭矩为
55 ± 7 N·m (41 ± 5 lb ft) 。 - 在接头 (3) 上安装 O 形密封圈。 将滤清器壳体 (2)和接头 (3)安装在壳体 (11)上。 安装螺栓 (8),并拧紧至扭矩为
55 ± 7 N·m (41 ± 5 lb ft) 。 - 将新的发动机机油滤清器芯安装到滤清器壳体 (2)中。
- 如有必要,将定位销安装在护盖 (7)中。 定位销必须在盖面以上
6.50 ± 1.00 mm (0.256 ± 0.040 in) 。 - 将 O 形密封圈安装在盖 (7) 上。 安装盖 (7) 和螺栓 (1)。
Show/hide table
图 1 | g01113975 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
结束:
- 安装发动机机油滤清器壳体。 参考拆解和组装, "发动机机油滤清器壳体 - 安装"。
Caterpillar Information System:
G3512H and G3516H Generator Set Engines Engine Oil Filter Housing - Disassemble
C9.3 Tier 4 Final Engines Cylinder Head Valves
2013/05/10 A New Water Seal Assembly Is Now Used on All 3408 and 3412 Engines {1100, 7555}
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
Failure of the Electronic Thermostat (ESTAT) on C175-16 Generator Set, Marine, and Petroleum Engines{135V} Failure of the Electronic Thermostat (ESTAT) on C175-16 Generator Set, Marine, and Petroleum Engines{135V}
C9.3 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Assemble
C9.3 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Maintenance Interval Schedule
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Washing System - Check
C9.3 Industrial Engine Engine Control Module - Remove and Install
G3512H and G3516H Generator Set Engines Engine Oil Pan - Remove and Install
G3512H and G3516H Generator Set Engines Engine Oil Pan - Disassemble
C13, C15, and C18 Tier 4 Final Engines Flywheel
C15 and C18 Industrial Engines Flywheel Housing
C9.3 Tier 4 Final Engines Flywheel
C9.3 Tier 4 Final Engines Flywheel
C9.3 Tier 4 Final Engines Flywheel
C9.3 Marine Engines Flywheel Housing
3176C and 3196 Engines for Caterpillar Built Machines Electric Starting Motor
C4.4 and C7.1 Engines Electrical Power Supply - Test
2013/07/22 A New Oil Mist Detector Mounting Bracket Is Used With Certain 3516C Engines {1336}