Cylinder Head Valves
Show/hide table
 | |
| 图 1 | g03365169 |
Show/hide table
| 345-2207 缸盖总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 24 | 247-9908 弹簧 | 在测试力下的长度为 67.12 mm (2.643 in)。 测试力为 320 ± 25 N (72 ± 6 lb)。 测试后的自由长度约为 76.70 mm (3.020 in)。 |
| 2 | 24 | 211-3122 弹簧 | 在测试力下的长度为 60.14 mm (2.368 in)。 测试力为 150 ± 12 N (34 ± 3 lb)。 测试后的自由长度约为 71.70 mm (2.823 in)。 |
| A | - | - | 从缸盖顶部至气门导管顶部的高度为 35.0 ± 0.5 mm (1.38 ± 0.02 in)。 |
| 3 | 24 | 122-7375 气门导管 | 装配前，将清洁的发动机机油涂覆到孔中。 气门导管中用于安装气门的孔径为 9.502 ± 0.013 mm (0.3741 ± 0.00051 in)。 |
| 4 | 12 | 153-7024 排气门 | 在安装到缸盖中之前，在气门杆上涂覆清洁的发动机机油。 端面角度为 45.75 ± 0.25 度。 气门杆直径为 9.441 ± 0.010 mm (0.3717 ± 0.0004 in)。 气门头直径为 41.81 ± 0.13 mm (1.646 ± 0.005 in)。 |
| 5 | 12 | 236-5605 进气门 | 在安装到缸盖中之前，在气门杆上涂覆清洁的发动机机油。 端面角度为 60.75 ± 0.25 度。 气门杆直径为 9.441 ± 0.010 mm (0.3717 ± 0.0004 in)。 气门头直径为 47.00 ± 0.13 mm (1.850 ± 0.005 in)。 |
| 6 | 12 | 226-5561 气门座镶圈 | 端面角度为 45.25 ± 0.25 度。 外径为 42.840 ± 0.013 mm (1.6866 ± 0.0005 in)。 缸盖中用于安装气门座镶圈的孔径为 42.774 ± 0.025 mm (1.6840 ± 0.0010 in)。 缸盖中用于安装气门座镶圈的孔深度为 13.90 ± 0.05 mm (0.547 ± 0.002 in)。 |
| 7 | 12 | 280-3979 气门座镶圈 | 端面角度为 30.25 ± 0.25 度。 外径为 48.025 ± 0.013 mm (1.8907 ± 0.0005 in)。 缸盖中用于安装气门座镶圈的孔径为 47.950 ± 0.025 mm (1.8878 ± 0.0010 in)。 缸盖中用于安装气门座镶圈的孔深度为 13.99 ± 0.05 mm (0.551 ± 0.002 in)。 |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
Failure of the Electronic Thermostat (ESTAT) on C175-16 Generator Set, Marine, and Petroleum Engines{135V} Failure of the Electronic Thermostat (ESTAT) on C175-16 Generator Set, Marine, and Petroleum Engines{135V}
C9.3 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Assemble
C9.3 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Maintenance Interval Schedule
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Washing System - Check
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Object Detection Sensor - Inspect/Adjust
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Object Detection Sensor - Clean/Inspect
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Camera - Inspect/Adjust
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Camera - Clean
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Display - Clean
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
2013/05/10 A New Water Seal Assembly Is Now Used on All 3408 and 3412 Engines {1100, 7555}
C9.3 Tier 4 Final Engines Cylinder Head Valves
G3512H and G3516H Generator Set Engines Engine Oil Filter Housing - Disassemble
G3512H and G3516H Generator Set Engines Engine Oil Filter Housing - Assemble
C9.3 Industrial Engine Engine Control Module - Remove and Install
G3512H and G3516H Generator Set Engines Engine Oil Pan - Remove and Install
G3512H and G3516H Generator Set Engines Engine Oil Pan - Disassemble
C13, C15, and C18 Tier 4 Final Engines Flywheel
C15 and C18 Industrial Engines Flywheel Housing
C9.3 Tier 4 Final Engines Flywheel
C9.3 Tier 4 Final Engines Flywheel