Rocker Shaft and Pushrod - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 235-0032 | 气门间隙仪表总成 | 1 |
B | 298-5564 | T40 Torx 套筒 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁气门桥。 检查气门桥有无磨损或损坏。 更换所有损坏或磨损的气门桥。
Show/hide table
图 1 g03412377 - 用清洁的发动机机油润滑气门桥 (4)。
Show/hide table
图 2 g03412379 Show/hide table注意 如未能将所有阀桥正确安装至阀杆上,将导致活塞和阀门间产生干扰,从而损坏发动机。
- 将气门桥 (4) 安装到缸盖上。
注: 将旧气门桥安装在原来的位置和朝向。 确保气门桥正确座入气门。 新气门桥可以安装为任意朝向。
为便于显示,没有显示电子单体喷油器。
- 清洁推杆。 检查推杆有无磨损或损坏。 更换任何磨损或损坏的推杆。
- 使用清洁的发动机机油润滑推杆 (3) 的两端。 将推杆的杯口朝上安装到发动机上。
注: 确保已将推杆 (3) 安装到原来的位置,并且每个推杆的球端都在气门挺杆中正确就座。
Show/hide table图 3 g01340040 Show/hide table图 4 g01340044 Show/hide table图 5 g03373790 摇臂轴拧紧顺序 - 确保摇臂轴组件清洁且无磨损或损坏。 将 torx 螺钉 (1) 安装到摇臂轴上。
- 将摇臂轴组件 (2) 安置在缸盖上。 固定夹 (6) 应面向发动机前部。
注: 确保调节螺钉 (5) 正确座入推杆 (3) 两端。
- 逐步拧紧 torx 螺钉 (1)。 为避免摇臂轴组件 (2) 变形,按图 5 所示的顺序拧紧 torx 螺钉。
拧紧 torx 螺钉 (1) 至扭矩为
35 N·m (26 lb ft) 。Show/hide table图 6 g01340045 - 使用工具 (A) 检查气门间隙。 请参阅系统操作、测试和调整发动机气门间隙, " - 检查 / 调整"。
- 必要时,使用工具 (A) 和工具 (B) 调整气门间隙。 请参阅系统操作、测试和调整, "发动机气门间隙 - 检查 / 调整"以了解正确程序。
结束:
- 安装气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
Caterpillar Information System:
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies System Fuses (MMS System Cabinet)
C7.1 Engines Rocker Shaft - Disassemble
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (MMS System Cabinet)
C7.1 Engines Rocker Shaft - Assemble
C7.1 Engines Relief Valve (Fuel) - Remove and Install
C7.1 Engines Refrigerant Compressor - Remove and Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (MMS System Cabinet)
C7.1 Engines Rear Power Take-Off (RPTO) - Remove
C7.1 Engines Rear Power Take-Off (RPTO) - Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Gen Set Module Circuit Breaker (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies External Source Sync Relay and Terminal Block
C7.1 Engines Pistons and Connecting Rods - Remove
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Front Panel Display (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Purpose Interface PWA (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies EPO Reset Switch (MMS System Cabinet)
2013/03/22 A New Turbo Kit is Available for Certain 3500B Engines {1052, 1053}
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Fan Monitor PWA (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Parallel Cabinet Controller PWA
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Parallel Cabinet Interface PWA
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Power Distribution PWA (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies AC Interface PWA (MMS System Cabinet)
C7.1 Engines Rocker Shaft and Pushrod - Remove
C7.1 Engines Turbocharger - Install - Turbocharger for Side Mounted Engines
C7.1 Engines Turbocharger - Remove - Turbocharger for Side Mounted Engines