Gen Set Module Circuit Breaker (Input/Output Cabinet)
Show/hide table
Illustration 1 | g03604657 |
I/O cabinet
Generator set module (GSM) option
The generator set module start option (1) adds the following breakers to the I/O cabinet:
- One breaker
- Two breakers (CB11 and CB21)
The breakers are located on the front panel at the bottom of the cabinet behind the door. Refer to Illustration 1 for the location. The GSM start option (1) allows the UPS to control generators in cases of lost utility power. Also, the GSM start option (1) allows the UPS to start the external generator set if power is lost.
Refer to the following list of characteristics for the circuit breakers:
- 480 VAC
- 40 A
- 3 - pole
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Input/Output Cabinet)" in order to shut down the system and gain access to internal components.
- Disconnect the six wires that lead to the circuit breaker and from the circuit breaker. Verify the labeling on the wires with the location of the wires. Verify the labeling on the cables for subsequent installation.
- Remove the four screws on the front of the breaker that secure the breaker to the rear of the cabinet.
- Attach the GSM circuit breaker (1) to the panel of the cabinet with four screws. Refer to Illustration 2.
Show/hide table
Illustration 3 g03797531 Generator set module (GSM) breaker found in some units
(4) Breaker attachment screws
(5) Cable connector screws - Connect the wires from the cable landing and the generator set. Verify the labeling of the wires with the location of the wires.
Show/hide table
Illustration 2 | g01271290 |
GSM panel (2) GSM breaker 1 (3) GSM breaker 2 |
Caterpillar Information System:
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies External Source Sync Relay and Terminal Block
C7.1 Engines Pistons and Connecting Rods - Remove
C7.1 Engines Pistons and Connecting Rods - Install
C7.1 Engines Pistons and Connecting Rods - Disassemble
C7.1 Engines Pistons and Connecting Rods - Assemble
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Fan (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Isolation Switches
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Fan Transformer
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies System Fuse (Input/Output Cabinet)
C7.1 Engines Piston Cooling Jets - Remove and Install
C7.1 Engines Lifter Group - Remove and Install
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Fuel Injector
C7.1 Engines Rear Power Take-Off (RPTO) - Install
C7.1 Engines Rear Power Take-Off (RPTO) - Remove
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (MMS System Cabinet)
C7.1 Engines Refrigerant Compressor - Remove and Install
C7.1 Engines Relief Valve (Fuel) - Remove and Install
C7.1 Engines Rocker Shaft - Assemble
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (MMS System Cabinet)
C7.1 Engines Rocker Shaft - Disassemble
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies System Fuses (MMS System Cabinet)
C7.1 Engines Rocker Shaft and Pushrod - Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Front Panel Display (MMS System Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Purpose Interface PWA (MMS System Cabinet)