Idler Gear - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 230-6284 | 正时销(凸轮轴) | 1 |
B | 136-4632 | 正时销(曲轴) | 1 |
268-1966 | 适配器 | 1 | |
C | 298-5564 | T40 Torx 套筒 | 1 |
开始:
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"以了解正确步骤。
- 拆下气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
注: 必须小心操作,确保在拆下惰轮时不会改变喷油泵正时。 小心地按照本步骤拆卸燃油泵齿轮。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将螺塞 (2) 从缸体上拆下,然后将 O 形密封圈 (1) 从螺塞上拆下。
- 旋转曲轴,使一号活塞处于压缩冲程的上止点。 有关正确的步骤,请参阅系统操作、测试和调整, "查找 1 号活塞上止点位置"。
- 将工具 (B) 安装到缸体的孔 (Y) 中。 使用工具 (B),将曲轴锁定到位。
注: 安装工具 (B) 时不要使用过大的力量。 在修理过程中不要使用工具 (B) 固定曲轴。
- 将工具 (A) 安装在凸轮轴齿轮 (3) 的孔 (X) 中。 使用工具 (A) 将凸轮轴锁定到位。
- 标记齿轮 (3)、齿轮 (4) 和齿轮 (5) 以便显示对准位置。 参考图 2。
Show/hide table
图 3 g03378317 - 松开所有摇臂 (8) 上的螺母 (7)。 用工具 (B )拧松所有摇臂 (8) 上的调节器 (6)。 拧松所有摇臂 (8) 上的调节器 (6),直到所有气门完全闭合。
注: 如果不能保证完全拧松所有调节器,可能会导致气门与活塞接触。
Show/hide table图 4 g03414039 Show/hide table图 5 g03414044 - 标记板 (9) 以显示朝向。
注: 识别标记能确保将板安装在原来的对准位置。
- 拆下螺栓 (10)。
- 拆下板 (9)。
- 拆下惰轮组件 (3)。
- 将轮毂 (11) 从惰齿轮 (3) 上卸下。
Show/hide table
图 1 | g01994555 |
Show/hide table
图 2 | g03414038 |
Caterpillar Information System:
C7.1 Engines Idler Gear - Install
C7.1 Engines Housing (Front) - Remove
C7.1 Engines Housing (Front) - Remove - Heavy Duty Housing (Front)
C7.1 Engines Housing (Front) - Install
C7.1 Engines Housing (Front) - Install - Heavy Duty Housing (Front)
C7.1 Engines Glow Plugs - Remove and Install
C7.1 Engines Gear Group (Front) - Remove and Install
C7.1 Engines Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C7.1 Engines Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 Engines Fuel Priming Pump - Remove and Install - Mechanical Priming Pump
C7.1 Engines Fuel Manifold (Rail) - Remove and Install
C7.1 Engines Fuel Injection Pump Gear - Remove
C7.1 Engines Idler Pulley - Remove and Install - Flat Idler Pulley
C7.1 Engines Idler Pulley - Remove and Install - Grooved Idler Pulley
C7.1 Engines Inlet Air Temperature Sensor - Remove and Install
C7.1 Engines Inlet and Exhaust Valve Springs - Remove and Install
C7.1 Engines Inlet and Exhaust Valves - Remove and Install
C7.1 Engines Inlet Manifold - Remove and Install
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Fuel Injector
C7.1 Engines Lifter Group - Remove and Install
C7.1 Engines Piston Cooling Jets - Remove and Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies System Fuse (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Fan Transformer
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Isolation Switches