Housing (Front) - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 6V-6640 | 密封胶 | 1 |
B | - | 导向螺柱 M8 × 40 mm |
2 |
C | 231-8847 | 定位工具 | 1 |
- | 螺栓 M10 × 50 mm |
3 | |
D | 1U-6396 | O 形圈组装固定胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
确保导线线束布线正确,且电缆带未过分拧紧。 过分拧紧电缆带会损坏导线线束卷。 |
- 确保前壳体清洁且无损坏。 如有必要,更换前壳体。
必要时,将封口塞安装到新的前壳体上。 使用工具 (A) 密封所有 D 形塞。
- 清洁缸体的所有密封垫表面。
Show/hide table
图 1 g03378741 Show/hide table图 2 g03378743 - 检查定位销 (12) 和定位销 (13) 有无损坏。 如有必要,更换缸体中的定位销。
- 将止推垫圈 (11) 安装到缸体的凹槽中。 更多信息请参阅拆解和组装, "凸轮轴 - 安装"。
- 将工具 (B) 安装到缸体上。 参考图 2。
- 将新密封垫 (10) 与工具 (B) 对齐。 将密封垫安装到缸体上。
注: 确保密封垫上的两个圆形凸舌 (X) 与缸体上的两个孔 (Y) 接合。 确保缸体中的定位销 (12) 在密封垫上接合。
- 将工具 (C) 安装到缸体上。
Show/hide table
图 3 g03378746 (6) M8 × 20 mm
(7) M8 × 35 mm
(8) M8 × 25 mmShow/hide table图 4 g03430987 - 将前壳体 (3) 从工具 (B) 和工具 (C) 的上方安装到缸体上。
- 将新螺栓 (8) 安装到前壳体 (3),用手拧紧。
- 拆下工具 (B)。
- 松松地安装螺栓 (6) 和螺栓 (7),用手拧紧。 有关螺栓的正确位置,请参阅插图 3。
- 按图 4 所示的顺序拧紧螺栓 (6)、螺栓 (7) 和螺栓 (8) 至扭矩为
28 N·m (248 lb in) 。 - 将工具 (C) 从缸体上拆下。
Show/hide table
图 5 g03430098 - 将新 O 形密封圈 (4) 和 O 形密封圈 (5) 安装到旁通管 (1) 上。 使用工具 (D) 润滑 O 形密封圈。
- 将旁通管 (1) 安装到缸盖和前壳体 (3) 上。 安装螺栓 (3)。 拧紧螺栓至扭矩为
22 N·m (195 lb in) 。
结束:
- 安装燃油喷油泵。 有关正确的步骤,请参阅拆解和组装, "燃油喷油泵 - 安装"。
- 安装正时齿轮。 有关正确步骤,请参阅拆解和组装, "齿轮总成(前)- 安装"。
- 如果发动机配备了附件驱动器,安装该附件驱动器。 有关正确步骤,请参阅拆解和组装, "附件驱动器 - 拆卸和安装"。
- 安装发动机油底壳护板。 有关正确步骤,请参阅拆解和组装, "发动机油底壳护板 - 拆卸"。
- 安装曲轴皮带轮。 请参阅拆解和组装, "减振器和皮带轮 - 安装",以了解正确的步骤。。
- 安装水泵。 请参阅拆解和组装, "水泵 - 安装",以了解正确的步骤。
- 安装风扇。 请参阅拆解和组装, "风扇 - 拆卸和安装",以了解正确的步骤。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液 - 加注"以了解正确程序。
Caterpillar Information System:
C7.1 Engines Housing (Front) - Install - Heavy Duty Housing (Front)
C7.1 Engines Glow Plugs - Remove and Install
C7.1 Engines Gear Group (Front) - Remove and Install
C7.1 Engines Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C7.1 Engines Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 Engines Fuel Priming Pump - Remove and Install - Mechanical Priming Pump
C7.1 Engines Fuel Manifold (Rail) - Remove and Install
C7.1 Engines Fuel Injection Pump Gear - Remove
C7.1 Engines Fuel Injection Pump Gear - Install
C7.1 Engines Fuel Injection Pump - Remove
C7.1 Engines Fuel Injection Pump - Install
C7.1 Engines Fuel Injection Lines - Remove
C7.1 Engines Housing (Front) - Remove - Heavy Duty Housing (Front)
C7.1 Engines Housing (Front) - Remove
C7.1 Engines Idler Gear - Install
C7.1 Engines Idler Gear - Remove
C7.1 Engines Idler Pulley - Remove and Install - Flat Idler Pulley
C7.1 Engines Idler Pulley - Remove and Install - Grooved Idler Pulley
C7.1 Engines Inlet Air Temperature Sensor - Remove and Install
C7.1 Engines Inlet and Exhaust Valve Springs - Remove and Install
C7.1 Engines Inlet and Exhaust Valves - Remove and Install
C7.1 Engines Inlet Manifold - Remove and Install
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Fuel Injector
C7.1 Engines Lifter Group - Remove and Install