Fuel Injection Pump Gear - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 230-6284 | 正时销(凸轮轴) | 1 |
C | 136-4632 | 正时销(曲轴) | 1 |
268-1966 | 适配器 | 1 | |
F | 8T-5096 | 千分表总成 | 1 |
- | 磁性座和支架 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 必须小心操作,确保在安装燃油泵齿轮时不会改变喷油泵正时。 小心遵循步骤安装燃油泵齿轮。
- 确保 1 号活塞在其压缩冲程的上止点位置。 有关正确的步骤,请参阅系统操作、测试和调整, "查找 1 号活塞上止点位置"。
- 将工具 (C) 穿过孔 (W) 安装,以锁定曲轴。
注: 安装工具 (C) 时不要使用过大的力量。 在修理过程中不要使用工具 (C) 固定曲轴。
Show/hide table图 2 g03383730 Show/hide table图 3 g03385332 正时标记的对准 - 将工具 (B) 穿过凸轮轴齿轮 (3) 的孔 (X) 安装到前壳体中。 使用工具 (B) 将凸轮轴锁定到位。
- 确保燃油泵 (8)(未显示)的轴清洁且无损坏。
- 确保燃油泵齿轮 (5) 清洁且无磨损损坏。 如有必要,更换燃油泵齿轮。
- 将燃油泵齿轮 (5) 安装到喷油泵 (8)(未显示)。
- 确保齿轮 (3)、齿轮 (4) 和齿轮 (5) 上的正时标记都已对齐,且齿轮相互啮合正确。 参考图 3。
- 将新弹簧垫圈 (7)(未显示)安装到燃油泵齿轮 (5)。
- 安装螺母 (6) 并用手拧紧。
- 将工具 (B) 从凸轮轴上拆下,将工具 (C) 从曲轴上拆下。
- 用适当的工具防止发动机在拧紧螺母 (6) 时旋转。 拧紧螺母 (6) 至扭矩为
160 N·m (118 lb ft) 。 - 用工具 (F) 确保齿轮 (3)、齿轮 (4) 和齿轮 (5) 的齿隙在规定值范围内。 更多信息请参阅技术规格, "齿轮总成(前)"。
- 使用清洁的发动机机油润滑齿轮的轮齿。
Show/hide table
图 4 g03383731 - 将新的 O 形密封圈 (1) 安装到螺塞 (2) 上。 将螺塞安装到缸体的孔 (W) 中。 拧紧螺塞 (2) 至扭矩为
21 N·m (186 lb in) 。
Show/hide table
图 1 | g03385331 |
结束:
- 安装前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"以了解正确步骤。
Caterpillar Information System:
C7.1 Engines Fuel Injection Pump - Remove
C7.1 Engines Fuel Injection Pump - Install
C7.1 Engines Fuel Injection Lines - Remove
C7.1 Engines Fuel Injection Lines - Install
C7.1 Marine Engine Engine Oil Filter Base - Remove and Install - M.C.S. Duplex Engine Oil Filter Base
C7.1 Engines Fuel Filter Base - Remove and Install
C7.1 Engines Front Cover - Remove and Install
C7.1 Engines Front Cover - Remove and Install - Heavy Duty Front Cover
C7.1 Engines Flywheel Housing - Remove and Install - Flywheel Housing that is Equipped with Rear Power Take-Off
C7.1 Engines Flywheel Housing - Remove and Install - Type A and Type B Wet Back End Housing
C7.1 Engines Flywheel - Remove
C7.1 Engines Flywheel - Remove - Equipped with Rear Power Take-Off
C7.1 Engines Fuel Injection Pump Gear - Remove
C7.1 Engines Fuel Manifold (Rail) - Remove and Install
C7.1 Engines Fuel Priming Pump - Remove and Install - Mechanical Priming Pump
C7.1 Engines Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 Engines Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C7.1 Engines Gear Group (Front) - Remove and Install
C7.1 Engines Glow Plugs - Remove and Install
C7.1 Engines Housing (Front) - Install - Heavy Duty Housing (Front)
C7.1 Engines Housing (Front) - Install
C7.1 Engines Housing (Front) - Remove - Heavy Duty Housing (Front)
C7.1 Engines Housing (Front) - Remove
C7.1 Engines Idler Gear - Install