- Excavator:
- 345BSeries II (S/N: ALB1-UP; CCC1-UP; ALD1-UP; AMD1-UP; FEE1-UP; AKJ1-UP; AMJ1-UP; CDJ1-UP; AMN1-UP; AYR1-UP; AGS1-UP; DCW1-UP; AKX1-UP)
- Mobile Hydraulic Power Unit:
- 345C MHPU (S/N: NRF1-UP; B6N1-UP)
- 345B (S/N: BFG1-UP; CFM1-UP; 4SS1-UP; 5WS1-UP; 6XS1-UP; 7KS1-UP; 9GS1-UP; 2NW1-UP; 2SW1-UP; 6MW1-UP; 8KW1-UP; 8RW1-UP; 9CW1-UP)
- 345C (S/N: TBA1-UP; FPC1-UP; MDC1-UP; SPC1-UP; ESD1-UP; WDE1-UP; TDG1-UP; GBH1-UP; GPH1-UP; TAJ1-UP; GCL1-UP; S5M1-UP; RFN1-UP; SCN1-UP; DHP1-UP; JAR1-UP; ELS1-UP; LYS1-UP; PJW1-UP; BWY1-UP)
- 345D (S/N: DPA1-UP; BYC1-UP; HLC1-UP; RGD1-UP; RAE1-UP; YEE1-UP; NEG1-UP; RGG1-UP; EEH1-UP; KFH1-UP; RAJ1-UP; MLK1-UP; NLM1-UP; JKN1-UP; L5R1-UP; FES1-UP; PBT1-UP; BYW1-UP; LKY1-UP)
- 349D (S/N: JGB1-UP; WTD1-UP; GKF1-UP; NNF1-UP; PZG1-UP; KLH1-UP; RBJ1-UP; MEN1-UP; KHS1-UP)
- 345D MHPU (S/N: P5D1-UP)
- 349D MHPU (S/N: DKN1-UP)
Description of Change: The new engine oil hoses and mounting hardware are used to help prevent against heat damage and abrasion damage from the lines contacting other components.
Adaptable To: The new 423-4640 Hose As and 423-4641 Hose As are a direct replacement for the existing 148-2104 Hose As and 144-0119 Hose As. This change is adaptable back to first production on the serial numbers listed above. Refer to Table 1 for a list of parts needed to install the new hose assemblies.
The removal procedure for existing hoses and the installation procedure for the new installing the new hose assemblies is shown below.
New Part Number     | Description     | Quantity     |
319-6220     | Elbow As     | 1     |
423-4640     | Hose As     | 1     |
423-4641     | Hose As     | 1     |
228-7093     | O-Ring Seal     | 1     |
6V-1889     | Clip     | 4     |
8T-7088     | Grommet     | 3     |
204-2281     | Cable Strap     | 3     |
Removal and Installation Procedure
- Remove the hose assemblies and mounting hardware indicated in Illustration 1.
Illustration 1 | g03340064 |
(1) Seal O-Ring (2) Clips (Retain the Bolts and Washers for reassembly) (3) Hose Assembly (4) Seal O-Ring (5) Adapter |
- Connect hoses (7) and (8) to the remote oil filter base.
Note: New O-ring (6) must be used connecting hose (8) .
Illustration 2 | g03340934 |
(6) 228-7093 O-Ring Seal (7) 423-4641 Hose As (8) 423-4640 Hose As (9) Two 8T-7088 Grommets (10) Two 204-2281 Cable Straps (11) Two 6V-1889 Clips (12) Two 8T-4121 Hard Washers (13) 8T-4136 Bolt (14) 8T-4133 Nut (15) 319-6220 Elbow As |
- Route hoses (7) and (8) and secure the hoses to the bracket where shown using clips (11), washers (12), bolts (13), and nut (14) .
Note: Bolts (113) and washers (12) were retained from the removal of the old parts.
- Install connector (15) into the oil line adapter. Connect the hoses to the connectors as shown.
- Install grommets (9) and cable straps (10) as shown in Illustration 2.