Flywheel - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M12 - 1.25 - X 100 mm |
2 |
B | 138-7573 | 连杆支架 | 1 |
注: 参考技术规格, "发动机设计",了解非指定的发动机扭矩值。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将两个螺栓 (2) 从飞轮 (1) 上拆下。
Show/hide table
图 2 g02798921 - 将工具 (A) 安装在曲轴中。
- 将工具 (B) 和适当的起吊设备安装到飞轮 (1) 上。 飞轮 (1) 的重量约为
30 kg (66 lb) 。 - 拆下其余的螺栓 (2)。
- 将飞轮 (1) 从缸体上拆下。
Show/hide table
图 3 g02798923 - 检查飞轮 (1) 和齿圈 (3) 有无磨损或损坏。 更换任何磨损或损坏的部件。
- 如有必要,拆下飞轮齿圈 (3),遵循步骤 7a 至步骤 7b。
- 将飞轮组件放置在适当的支架上。
- 使用锤子和冲头以将齿圈 (3) 从飞轮 (1) 上拆下。 如有必要,可能需要用喷枪加热齿圈 (3)。
注: 确定飞轮齿圈 (3) 上轮齿的方位。
Show/hide table
图 1 | g02794543 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M12 - 1.25 X 100 mm |
2 |
B | 138-7573 | 连杆支架 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 如果拆下飞轮齿圈 (3),按照步骤 1a 至 1c 将齿圈 (3) 安装到飞轮 (1) 上。
- 确定新齿圈 (3) 上轮齿的方位。
注: 安装飞轮时,齿圈轮齿的倒角侧必须朝向起动马达。 这将确保起动马达正确接合。
- 安装前,在烘箱中加热飞轮齿圈 (3) 至最高温度
250 °C (482 °F) 。注: 不要使用喷枪加热齿圈。
- 确保齿圈 (3) 的方向正确,并迅速将齿圈安装到飞轮 (1) 上。
Show/hide table图 5 g02798921 - 确定新齿圈 (3) 上轮齿的方位。
- 将工具 (B) 和适当的起吊设备安装到飞轮 (1) 上。 飞轮 (1) 的重量约为
30 kg (66 lb) 。 - 将工具 (A) 安装在曲轴中。
- 使用起吊设备将飞轮 (1) 安置在工具 (A) 上。
- 将螺栓 (2) 安装到飞轮 (1) 上。
- 拆下工具 (A)。
Show/hide table
图 6 g02794543 - 将其余螺栓 (2) 安装到飞轮 (1) 上。 向螺栓上涂覆发动机机油。 拧紧螺栓 (2) 至扭矩为
98 to 107 N·m (72 to 80 lb ft) 。
Show/hide table
图 4 | g02798923 |
Show/hide table
操作已经加热的零件时要坚持戴防护手套。 |
Caterpillar Information System:
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Remove - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Crankshaft Rear Seal and Wear Sleeve - Install - Includes Crankshaft Gear
C3.3B Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C3.3B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C3.3B Engines for Caterpillar Built Machines Idler Gear - Remove and Install
HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000} HVOF Identifier 396-9342 Group{0599, 0669, 0679, 7000}
C3.3B Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C3.3B Engines for Caterpillar Built Machines Bridge Dowels - Remove and Install
C1.5 and C2.2 Engines for Caterpillar Built Machines Diesel Particulate Filter - Clean
2014/05/30 Improved Camshafts Are Now Used on Certain C27 and C32 Machines {1210}
2014/05/30 An Improved Rocker Arm Assembly Is Used on C27 and C32 Machine Engines {1102, 1123}
C3.3B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C3.3B Engines for Caterpillar Built Machines Water Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C3.3B Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C3.3B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
2013/01/21 New Software is Available for Certain 3512C Petroleum Engines {1901, 1920}
C32 Auxiliary Engine Belts - Inspect/Adjust/Replace
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000} Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
2013/03/29 New Engine Oil Hoses Are Used on Certain Excavators Equipped with C13 Engines {1308}