Gear Group (Rear)
Show/hide table
 | |
| Illustration 1 | g03355599 |
Rear view of engine Typical example | |
Show/hide table
 | |
| Illustration 2 | g03355600 |
Typical example | |
Show/hide table
 | |
| Illustration 3 | g03355601 |
Typical example | |
Show/hide table
| Specification for 369-9363 Rear Gear Gp and 369-9365 Rear Gear Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 369-9356 Idler Gear As | After installation, bore of 125-9751 Bushing in the idler gear assembly is 81.060 ± 0.010 mm (3.1913 ± 0.0004 inch). Installation depth of the bushing is 1.00 ± 0.25 mm (0.049 ± 0.010 inch). |
| 2 | 4 | 8M-2530 Bolt | Torque to 140 ± 10 N·m (103 ± 7 lb ft). |
| 3 | 2 | 368-6914 Camshaft Drive Gear | Before assembly, clean the taper of the camshaft and the tapered bore of the camshaft drive gear with lint free cloth saturated with cleaning solvent to remove excess oil. Clean with alcohol wipe. Refer to Disassembly and Assembly for the installation procedure for the left and right camshaft drive gear . |
| 4 | 2 | 9X-8887 Bolt | Use the following procedure to tighten the bolt for the camshaft drive gears: 1. Tighten the bolt for the camshaft drive gear to 360 ± 40 N·m (266 ± 30 lb ft). 2. Mark a vertical line on the head of the bolt for the camshaft drive gear. Refer to Illustration 2. 3. Place a driver against the retaining plate of the camshaft drive gear. Strike the driver solidly with a hammer 3 to 4 times. 4. Again, tighten the bolt for the camshaft drive gear to 360 ± 40 N·m (266 ± 30 lb ft). 5. Repeat Step 3 and Step 4 until the mark on the bolt turns a minimum of 90 degrees. Refer to Illustration 3. |
| 5 | 4 | 1B-4367 Bolt | Torque to 240 ± 20 N·m (177 ± 15 lb ft). |
| 6 | 1 | 369-9357 Idler Gear As | After installation, bore of 101-1372 Bushing in the gear assembly is 75.060 ± 0.010 mm (2.9551 ± 0.0004 inch). Installation depth of the bushing is 1.5 ± 0.5 mm (0.06 ± 0.02 inch). |
| 7 | 2 | 101-1367 Idler Shaft | Diameter is 81.000 ± 0.010 mm (3.1890 ± 0.0004 inch). |
| 8 | 1 | 101-1365 Thrust Plate | Thickness of the new thrust plate is 6.35 ± 0.25 mm (0.250 ± 0.010 inch). |
| 9 | 2 | 8S-2331 Bolt | Torque to 240 ± 20 N·m (177 ± 15 lb ft). |
| 10 | 2 | 101-1368 Thrust Washer | Thickness of the new thrust washer is 1.90 ± 0.10 mm (0.075 ± 0.004 inch). |
| 11 | 1 | 101-1366 Gear Shaft | Diameter is 74.990 ± 0.010 mm (2.9524 ± 0.0004 inch). |
Caterpillar Information System:
C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Temperature Is High
C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft
C1.5 and C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover
C27 and C32 Industrial Engines Engine Oil Level - Check
2012/12/21 A New Piston, Piston Rings, and Cylinder Liner Are Used with Certain G3516E and G3520E Engines {1201, 1214, 1215, 1216}
2013/01/10 TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
C18 Marine Auxiliary and Marine Generator Set Engines Engine Valve Lash - Inspect/Adjust
C27 and C32 Industrial Engines Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C175-16 Locomotive Engine Electrical Power Supply - Test
C27 and C32 Generator Sets Coolant Sample (Level 1) - Obtain
C175-16 Locomotive Engine Water Lines
C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft
C1.5 and C2.2 Engines for Caterpillar Built Machines Main Bearing Journal
C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
3500 Marine Engines Turbocharger
C1.5 and C2.2 Engines for Caterpillar Built Machines Cylinder Block
C1.5 and C2.2 Engines for Caterpillar Built Machines Cylinder Head
C1.5 and C2.2 Engines for Caterpillar Built Machines Cylinder Head Valves
C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve
C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator
C175-16 Locomotive Engine Component Location
C175-16 Locomotive Engine Inlet Manifold
O-Rings - Radial, Fitting Assembly O-Rings and Other O-Ring Applications {0599, 0738, 4000, 4250, 4300, 5050, 5057, 7555} O-Rings - Radial, Fitting Assembly O-Rings and Other O-Ring Applications {0599, 0738, 4000, 4250, 4300, 5050, 5057, 7555}