Camshaft
Show/hide table
Illustration 1 | g00819857 |
Typical example |
(1) Height of the camshaft lobe for the inlet and exhaust valves
- C1.5 and C2.2 ...
34.065 to 34.120 mm (1.3411 to 1.3433 inch)
- C1.5 and C2.2 ...
33.7 mm (1.3270 inch)
Service limit
(2) Height of the camshaft lobe for the fuel injection pump
- C1.5, and C2.2 ...
41.940 to 42.060 mm (1.6512 to 1.6559 inch)
- C1.5 and C2.2 ...
41.8 mm (1.6450 inch)
Service limit
(3) Height of the camshaft lobe for the fuel transfer pump
- C1.5 and C2.2 ...
31.900 to 32.000 mm (1.2559 to 1.2598 inch)
- C1.5 and C2.2 ...
30.0 mm (1.1810 inch)
Service limit
Show/hide table
Illustration 2 | g00295323 |
Typical example |
(A) Actual camshaft lobe lift
(B) Height of the camshaft lobe
(C) Base circle
To determine the lobe lift, use the procedure that follows:
- Measure the height of the camshaft lobe (B).
- Measure the base circle (C).
- Subtract the base circle that is found in Step 2 from the height of the camshaft lobe that is found in Step 1. The difference is the actual camshaft lobe lift.
Show/hide table
Illustration 3 | g01297670 |
Typical example |
(4) Tighten the setscrews for the retainer plate for the camshaft to the following torque. ...
(5) Retainer plate for the camshaft
(6) Camshaft gear
Caterpillar Information System:
C175-16 Locomotive Engine Engine Oil Lines
C175-16 Marine Engine Junction Box
G3500 Engines Air Starting Motor
C175-16 Locomotive Engine Flywheel Housing Cover
2013/03/27 A New Seal Improves Starter Durability on Certain Industrial Engines {1453, 7555}
C175-16 Locomotive Engine Configuration Parameters
C175-16 Locomotive Engine Electrical Connectors
C27 and C32 Industrial Engines and C32 Petroleum Engine Refill Capacities
3516B Engine Air Conditioner Compressor - Remove and Install
Retrofitting for the Dynamic Gas Blending Capability on Certain 3512B Engines{1250, 1280} Retrofitting for the Dynamic Gas Blending Capability on Certain 3512B Engines{1250, 1280}
3516B Engine Water Temperature Regulators - Install
Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain C175-16 Generator Sets{1050, 1091} Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain C175-16 Generator Sets{1050, 1091}
C175-16 Locomotive Engine Water Lines
C27 and C32 Generator Sets Coolant Sample (Level 1) - Obtain
C175-16 Locomotive Engine Electrical Power Supply - Test
C27 and C32 Industrial Engines Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C18 Marine Auxiliary and Marine Generator Set Engines Engine Valve Lash - Inspect/Adjust
2013/01/10 TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
2012/12/21 A New Piston, Piston Rings, and Cylinder Liner Are Used with Certain G3516E and G3520E Engines {1201, 1214, 1215, 1216}
C27 and C32 Industrial Engines Engine Oil Level - Check
C1.5 and C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover
C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft
C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Temperature Is High
3516B Engine for the MT4400D Off-Highway Truck Gear Group (Rear)