Prelubrication Pump Problem
使用此步骤对低预润滑机油压力进行故障诊断与排除。 此外,如果下列事件代码激活,使用此步骤。
Show/hide table
事件代码 | ||
---|---|---|
CDL 代码和描述 | 产生此代码的状况 | 系统响应 |
E233(3) 发动机预润滑压力低 | 在编程的持续时间内,电子控制模块 (ECM) 没有检测到发动机预润滑顺序的最低压力。 | 记录该代码。
发动机将无法起动。 |
- 发动机机油油位
- 预润滑马达的电源
- 预润滑压力不足
注: 下面以概率的先后顺序列出了这些步骤。 按所列测试步骤中的顺序完成这些步骤。
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
---|---|---|
1. 检查代码 A. 将 Caterpillar 电子技师(ET)连接到维修工具接头上。 如有必要,请参阅故障诊断与排除, "电子维修工具"。 B. 在执行任何故障诊断与排除或清除故障诊断代码前,从发动机 ECM 下载"产品状态报告"。 C. 确定指向此描述的事件代码是否存在。 D. 针对指向此描述的事件代码,检查有无系统相关的激活诊断代码。 |
E233 |
结果:存在相关代码。 修理:在继续进行此测试前,诊断并排除所有相关代码。 结果:存在 E233 代码。 转至下一步。 结果:没有激活的代码 停止 |
2. 检查发动机机油油位 |
液位 |
结果:机油油位不低。 转至下一步。 结果:机油油位低。 修理:加注机油以获得正确的机油油位。 有关发动机机油的建议,参考操作和保养手册, "发动机机油"。 起动发动机。 检查发动机外部是否漏油。 修理漏油处。 如果故障未得到排除,转至下一步骤。 |
3. 检查预润滑泵电机的电源 A. 确保预润滑泵接线正确。 请参考故障诊断与排除, "预润滑 - 测试"以了解与泵电路相关的信息。 |
功率 |
结果:泵在需要时通电。 转至下一步。 结果:泵在需要时未通电。 修理:修理或更换有故障的电路部件。 如果故障未得到排除,转至下一步骤。 |
4. 检查预润滑压力是否不足 A. 预润滑循环期间,监视下述参数: "发动机机油压力(绝对)" 注:拖动发动机前,ECM 在编程设定的 "Engine Ready to Start Prelube Duration(发动机准备起动预润滑持续时间)"内必须检测到 |
压力 |
结果:压力不正常。 修理:修理或更换泵。 |
Caterpillar Information System:
C175-16 Marine Propulsion Engines Secondary ECM Assumes Control
C175-16 Marine Propulsion Engines Turbocharger Turbine Temperature Is High
C18 Generator Sets Model View Illustrations
C27 and C32 Generator Sets Configuration Parameters
C175-16 Locomotive Engine Valve Lash Is Excessive
C175-16 Locomotive Engine Valve Rotator or Spring Lock Is Free
2012/03/02 Design Changes to the Electronic Thermostat on C175-16 Generator Set Engines {135V, 4490, 5927}
307D Excavator Machine System Specifications Cylinder Mounting - Thumb
307D Excavator Machine System Specifications Quick Coupler
2012/11/09 Using the Correct Part Numbers for Making Fuel Hoses from Bulk Hose Stock on Certain C32 Commercial Engines {1274}
PMG3516 Power Module Spark Plugs - Inspect/Replace
PMG3516 Power Module Engine Oil Level - Check
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408} Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
C175-16 Locomotive Engine Oil Consumption Is Excessive
C175-16 Marine Propulsion Engines Fuel Rail Pressure Leakage Is High
C18 Generator Sets Safety Messages
3512B and 3512C Petroleum Generator Set Engines Fuel Filter Is Restricted
C2.6 and C3.3B Tier 2 and EU Stage 2 Engines for Caterpillar Built Machines Lubrication System
568 Forest Machines Machine Systems Track - Connect - PPR2
C2.6 and C3.3B Tier 2 and EU Stage 2 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust - C3.3B Engines
3512C and 3516C Marine Auxiliary Engines Fuel Pressure Is Low
Failure of the Weld Nuts in the Exhaust Shields on C175-16 Petroleum Engines{1067} Failure of the Weld Nuts in the Exhaust Shields on C175-16 Petroleum Engines{1067}
3500E Marine Engines Control Panel - Marine Classification Society Control Panel (MCS Control Panel) (If Equipped)
C175-16 Marine Propulsion Engines Vibration Damper Guard