Housing (Rear) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 1 |
B | 1P-0520 | Driver Group | 1 |
C | 230-6262 | Sealant | 1 |
Start By:
- Remove the rear gears.
- Remove plug (1) and disconnect hose assembly (2).
- Attach Tooling (A) to Location (X). The weight of rear housing (3) is
84 kg (185 lb) . - Remove bolts (4) and remove rear housing (3).
Show/hide table
Illustration 3 g02749117 - Remove gasket (5).
- Remove dowels (6). Remove bearing sleeve (7) and the dowels.
Show/hide table
Illustration 1 | g02749164 |
Show/hide table
Illustration 2 | g02749166 |
- Install rear housing (3) in the reverse order of removal.
- Use Tooling (B) to install bearing sleeve (25).
Show/hide table
Illustration 4 g02749119 - Install gasket (23). Apply a continuous bead of Tooling (C) to Areas (Y). The sealant should span the entire width of the T-Joint .
Show/hide table
Illustration 5 g02749137 - Attach Tooling (B) to Location (X). The weight of rear housing (21) is
84 kg (185 lb) . - Position rear housing (3). Install bolts (4). Tighten bolts (4) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) using the sequence in Illustration 5.
Note: Make sure that the housing and the face of the block are free of contaminants prior to installation.
Note: Apply clean engine oil to the bearings and the shaft assemblies prior to installation on the engine.
- Use Tooling (B) to install bearing sleeve (25).
Caterpillar Information System:
2011/11/02 Coolant Additive is Now used on Certain Motor Graders {1352, 1395}
259D, 279D, 289D, 299D, 299D XHP, 299D2 and 299D2 XHP Compact Track Loaders, 257D, 277D, 287D, 297D, 297D XHP, 297D2 and 297D2 XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D, 272D XHP, 272D2 and 272D2 XHP Skid Steer Loaders Piston Pump (Work Tool) - High Flow
521B and 522B Track Feller Bunchers Machine Systems Swing Motor Relief Valve Pressure - Test and Adjust
793F CMD Off-Highway Truck/Tractor Braking System MID 116 - CID 0168 - FMI 04
C27 and C32 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
553C, 563C, and 573C Wheel Feller Bunchers TA2 Technical Inspection{1000, 7000, 753T} 553C, 563C, and 573C Wheel Feller Bunchers TA2 Technical Inspection{1000, 7000, 753T}
793F CMD Off-Highway Truck/Tractor Braking System MID 116 - CID 0168 - FMI 03
521B and 522B Track Feller Bunchers Machine Systems Pump Control (Output Flow) - Adjust
793F CMD Off-Highway Truck/Tractor Braking System MID 116 - CID 0168 - FMI 02
2011/12/21 Improved Air Conditioning (AC) System in 793D Off-Highway Trucks {1802}
521B and 522B Track Feller Bunchers Machine Systems Piston Pump (Constant Horsepower Flow Control) - Test and Adjust
793F CMD Off-Highway Truck/Tractor Braking System MID 116 - CID 0041 - FMI 04
521B and 522B Track Feller Bunchers Daily Inspection
299D and 299D XHP Compact Track Loaders and 272D and 272D XHP Skid Steer Loaders Machine Electronic Control System General Information
773G and 775G OFF-Highway Trucks Engine Supplement Hood - Remove and Install
521B and 522B Track Feller Bunchers Alternate Exit
Machine Preheater for Track Feller Bunchers Machine Preparation for Troubleshooting
299D and 299D XHP Compact Track Loaders and 272D and 272D XHP Skid Steer Loaders Machine Electronic Control System Features
R3000H Load Haul Dump Central Lubrication System - Lubricate - If Equipped
R3000H Load Haul Dump Circuit Breakers - Reset
R3000H Load Haul Dump Collet Pin Bolt Torque - Check
R3000H Load Haul Dump Cooling System Coolant Extender (ELC) - Add
R3000H Load Haul Dump Cooling System Coolant Level - Check
R3000H Load Haul Dump Cooling System Coolant (ELC) - Change