CG137-08 and CG137-12 Engines Caterpillar


Timing Gear Cover - Remove and Install

Usage:

CG137-08 FPL

拆卸步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     -     LOCTITE 5900 法兰密封胶     1    

开始:

  1. 拆下发动机支架。
  2. 拆下曲轴前密封和承磨衬套。
  3. 拆下水泵。
  4. 拆下交流发电机和支架。



    图 1g02712587

  1. 拆下凸轮轴转速传感器 (2) 。

  1. 拆下锁紧螺母 (1) 和螺栓 (5) 。

  1. 拆下螺栓 (4) ,然后拆下正时齿轮盖 (3) 。

安装步骤

  1. 按与拆卸相反的顺序安装正时齿轮盖 (3) 。

    1. 安装螺栓 (5) 前,将工具 (D) 涂覆到油底壳的边角。 更多说明,请参阅拆解和组装, "油底壳 - 拆卸和安装"。

    1. 用密封的润滑剂润滑凸轮轴转速传感器 (2) 的孔。 将凸轮轴转速传感器 (2) 拧紧至扭矩为 14 ± 3 N·m (124 ± 27 lb in)。

Caterpillar Information System:

CG137-08 and CG137-12 Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
C4.4 Marine Generator Set Before Starting Engine
C15 Engines for Combat and Tactical Vehicles Lubrication System
3516C Generator Sets Engine Crankcase Breather - Clean
3516C Generator Sets Glossary
C13, C15, and C18 Tier 4 Final Engines Front Housing and Covers
3516C Generator Set Engines Catalytic Converter Sensor
C13, C15, and C18 Tier 4 Final Engines Pressure Sensor (Exhaust Differential)
C9.3 Tier 4 Final Engines Flywheel Housing
CG137-08 and CG137-12 Generator Sets Flywheel
CG137-08 and CG137-12 Generator Sets Stub Shaft (Rear)
CG137-08 and CG137-12 Engines Timing Gears - Remove and Install
CG137-08 and CG137-12 Engines Valve Cover Base - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Rocker Shaft and Push Rod - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Cylinder Head - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Pistons and Connecting Rods - Remove and Install
CG137-08 and CG137-12 Engines Cylinder Liner - Remove and Install
CG137-08 and CG137-12 Engines Camshaft - Remove and Install
371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
CG137-08 and CG137-12 Engines Camshaft Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Main Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft - Remove and Install
TH55FT-E70 and TH55FT-E90 Transmissions Daily Inspection
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.