Wear Plates - Remove and Install
Start By:
- Remove the hydraulic hammer from the housing. Refer to Disassembly and Assembly, "Hydraulic Hammer - Remove".
- Inspect the wear plates for excessive wear. Refer to Service Manual, "Wear Plates" for the specifications of the plates. If the wear plates are worn excessively or the plates are damaged, the wear plates must be replaced.
- By reaching through the bottom of the hammer housing, use a suitable prybar to remove plates (1) to be replaced.
- Alternatively, wear plates (1) can be rotated to extend component life.
- Remove bottom damper (2).
Show/hide table
Illustration 1 | g02645998 |
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement, if necessary.
Show/hide table
Illustration 2 g02645998 - Install bottom damper (2). If installing new wear plates (1), place the wear plates into position on the pins in the lower end of hammer housing. Ensure that the wear plates do not cover any openings.
- Press or tap the new plates onto the pins in the housing.
- Alternatively, wear plates (1) can be rotated to extend component life.
End By:
- Install the hydraulic hammer into the hammer housing. Refer to the Disassembly and Assembly, "Hydraulic Hammer - Install".
Caterpillar Information System:
330D and 336D Excavators Machine System Specifications Hydraulic Generator
320E RR Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
Instructions for Replacing the Support Plate on Certain SW60 Wheel Saws{6712} Instructions for Replacing the Support Plate on Certain SW60 Wheel Saws{6712}
320E RR Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pads - Remove and Install
329E MHPU Mobile Hydraulic Power Unit Maintenance Interval Schedule
G3512 Gas Engine Flywheel
330D and 336D Excavators Machine System Specifications Stick Cylinder
330D and 336D Excavators Machine System Specifications Return and Oil Filter Lines
301.4C Mini Hydraulic Excavator Travel Motor
301.4C Mini Hydraulic Excavator Hydraulic System Breather - Replace
301.4C Mini Hydraulic Excavator Fuel Injection Nozzles - Check/Adjust
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Control Valve - Remove
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Control Valve - Install
G310B, G315B and G320B Demolition and Sorting Grapples Hydraulic Rotator Cycle Time - Check
G310B, G315B and G320B Demolition and Sorting Grapples Host Machine Pressure and Flow - Test
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Remove
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Install
Intake Manifold Pressure Shown Incorrectly in the Monitor Display of Certain Wheeled Excavators{7490, 7601, 7620} Intake Manifold Pressure Shown Incorrectly in the Monitor Display of Certain Wheeled Excavators{7490, 7601, 7620}
320E RR Excavator Hydraulic System Relief Valve (Crossover) - Test and Adjust
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Disassemble
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Assemble
320E RR Excavator Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
330D and 336D Excavators Machine System Specifications Hydraulic Generator